Adalight-FastLED_rgbwMod/Arduino/LEDstream_FastLED/LEDstream_FastLED.ino

/* LEDstream_FastLED
 * 
 * Modified version of Adalight protocol that uses the FastLED
 * library (http://fastled.io) for driving led strips.
 * 
 * http://github.com/dmadison/Adalight-FastLED
 * Last Updated: 2017-05-05
 */

// --- General Settings
static const uint8_t 
	Num_Leds   =  80,        // strip length
	Led_Pin    =  6,         // Arduino data output pin
	Brightness =  255;       // maximum brightness

// --- FastLED Setings
#define LED_TYPE     WS2812B // led strip type for FastLED
#define COLOR_ORDER  GRB     // color order for bitbang

// --- Serial Settings
static const unsigned long
	SerialSpeed    = 115200; // serial port speed, max available
static const uint16_t
	SerialTimeout  = 150;    // time before LEDs are shut off if no data (in seconds)

// --- Optional Settings (uncomment to add)
//#define CLEAR_ON_START     // LEDs are cleared on reset
//#define GROUND_PIN 10      // additional grounding pin (optional)
//#define CALIBRATE          // sets all LEDs to the color of the first

// --- Debug Settings (uncomment to add)
//#define DEBUG_LED 13       // toggles the Arduino's built-in LED on header match
//#define DEBUG_FPS 8        // enables a pulse on LED latch

// --------------------------------------------------------------------

#include <FastLED.h>

CRGB leds[Num_Leds];
uint8_t * ledsRaw = (uint8_t *)leds;

// A 'magic word' (along with LED count & checksum) precedes each block
// of LED data; this assists the microcontroller in syncing up with the
// host-side software and properly issuing the latch (host I/O is
// likely buffered, making usleep() unreliable for latch). You may see
// an initial glitchy frame or two until the two come into alignment.
// The magic word can be whatever sequence you like, but each character
// should be unique, and frequent pixel values like 0 and 255 are
// avoided -- fewer false positives. The host software will need to
// generate a compatible header: immediately following the magic word
// are three bytes: a 16-bit count of the number of LEDs (high byte
// first) followed by a simple checksum value (high byte XOR low byte
// XOR 0x55). LED data follows, 3 bytes per LED, in order R, G, B,
// where 0 = off and 255 = max brightness.

static const uint8_t magic[] = {
	'A','d','a'};
#define MAGICSIZE  sizeof(magic)

// Check values are header byte # - 1, as they are indexed from 0
#define HICHECK    (MAGICSIZE)
#define LOCHECK    (MAGICSIZE + 1)
#define CHECKSUM   (MAGICSIZE + 2)

#define MODE_HEADER 0
#define MODE_DATA   1

static uint8_t
	mode = MODE_HEADER;
static int16_t
	c;
static uint16_t
	outPos;
static uint32_t
	bytesRemaining;
static unsigned long
	t,
	lastByteTime,
	lastAckTime;

// Debug macros initialized
#ifdef DEBUG_LED
	#define ON  1
	#define OFF 0

	#define D_LED(x) do {digitalWrite(DEBUG_LED, x);} while(0)
#else
	#define D_LED(x)
#endif

#ifdef DEBUG_FPS
	#define D_FPS do {digitalWrite(DEBUG_FPS, HIGH); digitalWrite(DEBUG_FPS, LOW);} while (0)
#else
	#define D_FPS
#endif

void setup(){
	#ifdef GROUND_PIN
		pinMode(GROUND_PIN, OUTPUT);
		digitalWrite(GROUND_PIN, LOW);
	#endif

	#ifdef DEBUG_LED
		pinMode(DEBUG_LED, OUTPUT);
		digitalWrite(DEBUG_LED, LOW);
	#endif

	#ifdef DEBUG_FPS
		pinMode(DEBUG_FPS, OUTPUT);
	#endif

	FastLED.addLeds<LED_TYPE, Led_Pin, COLOR_ORDER>(leds, Num_Leds);
	FastLED.setBrightness(Brightness);

	#ifdef CLEAR_ON_START
		FastLED.show();
	#endif

	Serial.begin(SerialSpeed);
	Serial.print("Ada\n"); // Send ACK string to host

	lastByteTime = lastAckTime = millis(); // Set initial counters
}

void loop(){
	adalight();
}

void adalight(){ 
	t = millis(); // Save current time

	// If there is new serial data
	if((c = Serial.read()) >= 0){
		lastByteTime = lastAckTime = t; // Reset timeout counters

		switch(mode) {
			case MODE_HEADER:
				headerMode();
				break;
			case MODE_DATA:
				dataMode();
				break;
		}
	}
	else {
		// No new data
		timeouts();
	}
}

void headerMode(){
	static uint8_t
		headPos,
		hi, lo, chk;

	if(headPos < MAGICSIZE){
		// Check if magic word matches
		if(c == magic[headPos]) {headPos++;}
		else {headPos = 0;}
	}
	else{
		// Magic word matches! Now verify checksum
		switch(headPos){
			case HICHECK:
				hi = c;
				headPos++;
				break;
			case LOCHECK:
				lo = c;
				headPos++;
				break;
			case CHECKSUM:
				chk = c;
				if(chk == (hi ^ lo ^ 0x55)) {
					// Checksum looks valid. Get 16-bit LED count, add 1
					// (# LEDs is always > 0) and multiply by 3 for R,G,B.
					D_LED(ON);
					bytesRemaining = 3L * (256L * (long)hi + (long)lo + 1L);
					outPos = 0;
					memset(leds, 0, Num_Leds * sizeof(struct CRGB));
					mode = MODE_DATA; // Proceed to latch wait mode
				}
				headPos = 0; // Reset header position regardless of checksum result
				break;
		}
	}
}

void dataMode(){
	// If LED data is not full
	if (outPos < sizeof(leds)){
		dataSet();
	}
	bytesRemaining--;
 
	if(bytesRemaining == 0) {
		// End of data -- issue latch:
		mode = MODE_HEADER; // Begin next header search
		FastLED.show();
		D_FPS;
		D_LED(OFF);
	}
}

void dataSet(){
	#ifdef CALIBRATE
		if(outPos < 3)
			ledsRaw[outPos++] = c;
		else{
			ledsRaw[outPos] = ledsRaw[outPos%3]; // Sets RGB data to first LED color
			outPos++;
		}
	#else
		ledsRaw[outPos++] = c; // Issue next byte
	#endif
}

void timeouts(){
	// No data received. If this persists, send an ACK packet
	// to host once every second to alert it to our presence.
	if((t - lastAckTime) > 1000) {
		Serial.print("Ada\n"); // Send ACK string to host
		lastAckTime = t; // Reset counter

		// If no data received for an extended time, turn off all LEDs.
		if((t - lastByteTime) > SerialTimeout * 1000) {
			memset(leds, 0, Num_Leds * sizeof(struct CRGB)); //filling Led array by zeroes
			FastLED.show();
			lastByteTime = t; // Reset counter
		}
	}
}