flm01/mote/v2/avr/basiciotest.c

//
// basiciotest.c : test code for the io and buffer ops of the UART and SPI ports
//
// Copyright (c) 2010 flukso.net
//
// This program is free software; you can redistribute it and/or
// modify it under the terms of the GNU General Public License
// as published by the Free Software Foundation; either version 2
// of the License, or (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program; if not, write to the Free Software
// Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
//
// $Id$

#include <avr/io.h>
#include <avr/interrupt.h>
#include <avr/eeprom.h>

#include <util/delay.h>

#include "uart.h"
#include "spi.h"
#include "ctrl.h"


#define NO_OP_1		1
#define NO_OP_2		2
#define START_TX	4
#define TRANSMIT        8
#define HIGH_HEX	16
#define TO_FROM_UART	32
#define NEW_CTRL_MSG	64

#define SPI_END_OF_TX			0x00
#define SPI_END_OF_MESSAGE		'.'
#define SPI_FORWARD_TO_UART_PORT	'u'
#define SPI_FORWARD_TO_CTRL_PORT	'l' // 'l'ocal port

volatile uint8_t spi_status, high_hex;

// hex to binary/byte decoding
uint8_t htob(uint16_t hex)
{
	uint8_t low_hex = (uint8_t) hex;
	uint8_t high_hex = (uint8_t) (hex >> 8); 
	uint8_t byte;

	byte = (high_hex > 0x40) ? (high_hex & 0x0F) + 9 : high_hex & 0x0F;
	byte = byte << 4;
        byte |= (low_hex > 0x40) ? (low_hex & 0x0F) + 9 : low_hex & 0x0F;
	return byte;
}

// binary/byte to hex encoding
uint16_t btoh(uint8_t byte)
{
	uint8_t low_nibble = (byte & 0x0F);
	uint8_t high_nibble = (byte & 0xF0) >> 4;
	uint16_t hex;

	hex = (high_nibble > 0x09) ? high_nibble - 9 + 0x60 : high_nibble + 0x30;
	hex = hex << 8;
	hex |= (low_nibble > 0x09) ? low_nibble - 9 + 0x60 : low_nibble + 0x30;
	return hex;
}


ISR(SPI_STC_vect)
{
	uint8_t spi_rx, rx, tx; 
	uint16_t spi_tx;

	// the SPI is double-buffered, requiring two NO_OPs when switching from Tx to Rx
	if (spi_status & (NO_OP_1 | NO_OP_2)) {
		spi_status--;
		return;
	}

	// do we have to transmit the first byte?
	if (spi_status & START_TX) {
		received_from_spi(SPI_FORWARD_TO_CTRL_PORT);
		spi_status &= ~START_TX;
		return;
	}

	// are we in Tx mode?
	if (spi_status & TRANSMIT) {
		if (spi_status & HIGH_HEX) {
			received_from_spi(high_hex);
			spi_status &= ~HIGH_HEX;
			return;
		}

		if (spi_status & TO_FROM_UART) {
			if (!uartReceiveByte(&tx)) {
				received_from_spi(SPI_END_OF_TX);
				spi_status &= ~TRANSMIT;
				spi_status |= NO_OP_2;
				return;
			}
		}
		else {
			if (ctrlGetFromTxBuffer(&tx)) {
				if (tx == SPI_END_OF_MESSAGE) {
					received_from_spi(tx);
					return;
				}
			}
			else {
				received_from_spi(SPI_FORWARD_TO_UART_PORT);
				spi_status |= TO_FROM_UART;
				return;
			}
		}

		spi_tx = btoh(tx);
		high_hex = (uint8_t)spi_tx;
		spi_status |= HIGH_HEX;
		received_from_spi((uint8_t)(spi_tx >> 8));
		return;
	}

	// we're in Rx mode
	switch (spi_rx = received_from_spi(0x00)) {
		case SPI_END_OF_TX:
			spi_status |= TRANSMIT | START_TX; 
			spi_status &= ~(HIGH_HEX | TO_FROM_UART);
			break;
		case SPI_END_OF_MESSAGE:
			if (!(spi_status & TO_FROM_UART)) {
				ctrlAddToRxBuffer(spi_rx);
				spi_status |= NEW_CTRL_MSG;
			}
			break;
		case SPI_FORWARD_TO_UART_PORT:
			spi_status |= TO_FROM_UART;
			break;
		case SPI_FORWARD_TO_CTRL_PORT:
			spi_status &= ~TO_FROM_UART;
			break;
		default:
			if (spi_status & HIGH_HEX) {
				rx = htob(((uint16_t)high_hex << 8) + spi_rx);

				if (spi_status & TO_FROM_UART) {
					uartAddToTxBuffer(rx);
				}
				else {
					ctrlAddToRxBuffer(rx);
				}
			}
			else {
				high_hex = spi_rx;
			}
			// toggle the HEX bit in spi_status
			spi_status ^= HIGH_HEX;
	}
}

ISR(TIMER1_COMPA_vect)
{
	/* void */
}

ISR(ANALOG_COMP_vect)
{
	uint8_t i;

	PORTB |= (1<<PB0);

	//disable uC sections to consume less power while writing to EEPROM
	//disable UART Tx and Rx:
	UCSR0B &= ~((1<<RXEN0) | (1<<TXEN0));
	//disable ADC:
	ADCSRA &= ~(1<<ADEN);

	for (i=0; i<128; i++)
		eeprom_write_byte((uint8_t *)i, i); 			

	//enable UART Tx and Rx:
	UCSR0B |= (1<<RXEN0) | (1<<TXEN0);
	// enable ADC and start a first ADC conversion
	ADCSRA |= (1<<ADEN) | (1<<ADSC);

	PORTB &= ~(1<<PB0);
}

void setup_pulse_input(void)
{
	// PD2=INT0 and PD3=INT1 configuration
	// set as input pin with 20k pull-up enabled
	PORTD |= (1<<PD2) | (1<<PD3);
	// INT0 and INT1 to trigger an interrupt on a falling edge
	EICRA = (1<<ISC01) | (1<<ISC11);
	// enable INT0 and INT1 interrupts
	EIMSK = (1<<INT0) | (1<<INT1);
}


void setup_timer1(void)
{
	// Timer1 clock prescaler set to 1 => fTOV1 = 3686.4kHz / 65536 = 56.25Hz (DS p.134)
	TCCR1B |= (1<<CS10);
	// Increase sampling frequency to 2kHz (= 667Hz per channel) with an error of 0.01% (DS p.122)
	OCR1A = 0x0732;
	// Timer1 set to CTC mode (DS p.133)
	TCCR1B |= 1<<WGM12;
	// Enable output compare match interrupt for timer1 (DS p.136)
	TIMSK1 |= (1<<OCIE1A);
#if DBG > 0
	// Set PB1=OC1A as output pin
	DDRB |= (1<<DDB1);
	// Toggle pin OC1A=PB1 on compare match
	TCCR1A |= 1<<COM1A0;
#endif
}

void setup_analog_comparator(void)
{
	// analog comparator setup for brown-out detection
	// PD7=AIN1 configured by default as input to obtain high impedance

	// disable digital input cicuitry on AIN0 and AIN1 pins to reduce leakage current
	DIDR1 |= (1<<AIN1D) | (1<<AIN0D);

	// comparing AIN1 (Vcc/4.4) to bandgap reference (1.1V)
	// bandgap select | AC interrupt enable | AC interrupt on rising edge (DS p.243)
	ACSR |= (1<<ACBG) | (1<<ACIE) | (1<<ACIS1) | (1<<ACIS0);
}

int main(void)
{
	// RS-485: Configure PD5=DE as output pin with low as default
	DDRD |= (1<<DDD5);
	// set high to transmit
	//PORTD |= (1<<PD5);
	
	setup_timer1();
	setup_pulse_input();
	setup_analog_comparator();
		
	// initialize the CTRL buffers
	ctrlInit();
	// initialize the UART hardware and buffers
	uartInit();
	// initialize the SPI in slave mode
	setup_spi(SPI_MODE_0, SPI_MSB, SPI_INTERRUPT, SPI_SLAVE);


	for(;;) {
		if (spi_status & NEW_CTRL_MSG) {
			ctrlRxToTxLoop();
			spi_status &= ~NEW_CTRL_MSG;
		}
		
		// toggle the LED=PB0 pin
		_delay_ms(50);
		 DDRB ^= (1<<PB0);
	}

	return 0;
}