diff --git a/include/sensor_hcsr501.cpp b/include/sensor_hcsr501.cpp
index a29406a..c2cd01c 100644
--- a/include/sensor_hcsr501.cpp
+++ b/include/sensor_hcsr501.cpp
@@ -1,9 +1,11 @@
 // PIR Sensors HC-SR501
 // pir sensor needs 5v through an inductor for filtering. output level is 3.3v
-// 100nF capacitor SENSOR_HCSR501_minchangeshould be soldered between pins 12 and 13 of BISS0001 to stop interference from esp causing false triggers (in some setups). source: https://www.letscontrolit.com/forum/viewtopic.php?t=671
+// 100nF capacitor should be soldered between pins 12 and 13 of BISS0001 to stop interference from esp causing false triggers (in some setups). source: https://www.letscontrolit.com/forum/viewtopic.php?t=671
 // hc-sr501 should also be a few cm away from the esp. interference can cause false triggering
 // poti closer to jumper is sensitivity (cw increases). other poti is pulse time (cw increases).
+// Set jumper to inner position (closer to IC)
 // time set to output around 30s pulse
+// pinout is Vin, Signal, GND. Vin pin is closest to diode
 #include "sensor_hcsr501.h"
 
 
diff --git a/platformio.ini b/platformio.ini
index cb9f650..f119700 100644
--- a/platformio.ini
+++ b/platformio.ini
@@ -18,7 +18,8 @@
 #data_dir=data_sensoresp3
 #data_dir=data_sensoresp4
 #data_dir=data_sensoresp5
-data_dir=data_sensoresp6
+#data_dir=data_sensoresp6
+data_dir=data_sensoresp7
 #data_dir=data_sensoresp3dprinter
 #data_dir=data_sensoresptest
 
@@ -80,6 +81,7 @@ lib_deps =
     adafruit/Adafruit SHT31 Library@^2.2.0
     SPI
 
+    
 
 #Test
 [env:sensoresptest]
@@ -321,6 +323,38 @@ lib_deps =
     Homie@3.0.0
     claws/BH1750@1.1.4
 
+#Kueche
+[env:sensoresp7]
+platform = espressif8266 @ 2.5.0
+board = d1_mini
+framework = arduino
+
+#monitor_port = /dev/ttyUSB0
+monitor_port = COM3
+monitor_speed = 115200
+
+build_flags =
+    
+    -D SENSOR_HCSR501
+    -D SENSOR_HCSR501_PIN=D6
+
+    -D SENSOR_VL53L1X
+    -D SENSOR_VL53L1X_minchange=500
+    -D SENSOR_VL53L1X_senddelaymax=1000*30
+    -D SENSOR_VL53L1X_readdelay=500
+
+    -D SENSOR_SHT31
+    -D SENSOR_SHT31_humidity_minchange=5
+    -D SENSOR_SHT31_temperature_minchange=0.5
+
+lib_deps =
+    Bounce2
+    SPI
+    ArduinoJson@6.16.1
+    marvinroger/Homie @ ^3.0.1
+    pololu/VL53L1X @ ^1.3.0
+    adafruit/Adafruit SHT31 Library@^2.2.0
+
 #3D Printer
 [env:sensoresp3dprinter]
 platform = espressif8266 @ 2.5.0