nordic_fob example fully working.
This commit is contained in:
parent
36167a9e02
commit
d1653e8cad
|
@ -1,5 +1,5 @@
|
|||
/*
|
||||
Copyright (C) 2011 J. Coliz <maniacbug@ymail.com>
|
||||
Copyright (C) 2012 J. Coliz <maniacbug@ymail.com>
|
||||
|
||||
This program is free software; you can redistribute it and/or
|
||||
modify it under the terms of the GNU General Public License
|
||||
|
@ -7,17 +7,16 @@
|
|||
*/
|
||||
|
||||
/**
|
||||
* Example RF Radio Ping Pair
|
||||
* Example Nordic FOB Receiver
|
||||
*
|
||||
* This is an example of how to use the RF24 class. Write this sketch to two different nodes,
|
||||
* connect the role_pin to ground on one. The ping node sends the current time to the pong node,
|
||||
* which responds by sending the value back. The ping node can then see how long the whole cycle
|
||||
* took.
|
||||
* This is an example of how to use the RF24 class to receive signals from the
|
||||
* Sparkfun Nordic FOB. See http://www.sparkfun.com/products/8602 .
|
||||
* Thanks to Kirk Mower for providing test hardware.
|
||||
*/
|
||||
|
||||
#include <SPI.h>
|
||||
#include <RF24.h>
|
||||
#include "nRF24L01.h"
|
||||
#include "RF24.h"
|
||||
#include "printf.h"
|
||||
|
||||
//
|
||||
|
@ -26,96 +25,53 @@
|
|||
|
||||
// Set up nRF24L01 radio on SPI bus plus pins 9 & 10
|
||||
|
||||
RF24 radio(9,10);
|
||||
|
||||
// sets the role of this unit in hardware. Connect to GND to be the 'pong' receiver
|
||||
// Leave open to be the 'ping' transmitter
|
||||
const int role_pin = 7;
|
||||
RF24 radio(8,9);
|
||||
|
||||
//
|
||||
// Topology
|
||||
// Payload
|
||||
//
|
||||
|
||||
// Radio pipe addresses for the 2 nodes to communicate.
|
||||
const uint64_t pipes[2] = { 0xF0F0F0F0E1LL, 0xF0F0F0F0D2LL };
|
||||
struct payload_t
|
||||
{
|
||||
uint8_t buttons;
|
||||
uint16_t id;
|
||||
uint8_t empty;
|
||||
};
|
||||
|
||||
const char* button_names[] = { "Up", "Down", "Left", "Right", "Center" };
|
||||
const int num_buttons = 5;
|
||||
|
||||
//
|
||||
// Role management
|
||||
//
|
||||
// Set up role. This sketch uses the same software for all the nodes
|
||||
// in this system. Doing so greatly simplifies testing. The hardware itself specifies
|
||||
// which node it is.
|
||||
//
|
||||
// This is done through the role_pin
|
||||
// Forward declarations
|
||||
//
|
||||
|
||||
// The various roles supported by this sketch
|
||||
typedef enum { role_ping_out = 1, role_pong_back } role_e;
|
||||
uint16_t flip_endian(uint16_t in);
|
||||
|
||||
// The debug-friendly names of those roles
|
||||
const char* role_friendly_name[] = { "invalid", "Ping out", "Pong back"};
|
||||
|
||||
// The role of the current running sketch
|
||||
role_e role;
|
||||
//
|
||||
// Setup
|
||||
//
|
||||
|
||||
void setup(void)
|
||||
{
|
||||
//
|
||||
// Role
|
||||
//
|
||||
|
||||
// set up the role pin
|
||||
pinMode(role_pin, INPUT);
|
||||
digitalWrite(role_pin,HIGH);
|
||||
delay(20); // Just to get a solid reading on the role pin
|
||||
|
||||
// read the address pin, establish our role
|
||||
if ( ! digitalRead(role_pin) )
|
||||
role = role_ping_out;
|
||||
else
|
||||
role = role_pong_back;
|
||||
|
||||
//
|
||||
// Print preamble
|
||||
//
|
||||
|
||||
Serial.begin(57600);
|
||||
printf_begin();
|
||||
printf("\n\rRF24/examples/pingpair/\n\r");
|
||||
printf("ROLE: %s\n\r",role_friendly_name[role]);
|
||||
printf("\r\nRF24/examples/nordic_fob/\r\n");
|
||||
|
||||
//
|
||||
// Setup and configure rf radio
|
||||
// Setup and configure rf radio according to the built-in parameters
|
||||
// of the FOB.
|
||||
//
|
||||
|
||||
radio.begin();
|
||||
|
||||
// optionally, increase the delay between retries & # of retries
|
||||
radio.setRetries(15,15);
|
||||
|
||||
// optionally, reduce the payload size. seems to
|
||||
// improve reliability
|
||||
radio.setPayloadSize(8);
|
||||
|
||||
//
|
||||
// Open pipes to other nodes for communication
|
||||
//
|
||||
|
||||
// This simple sketch opens two pipes for these two nodes to communicate
|
||||
// back and forth.
|
||||
// Open 'our' pipe for writing
|
||||
// Open the 'other' pipe for reading, in position #1 (we can have up to 5 pipes open for reading)
|
||||
|
||||
if ( role == role_ping_out )
|
||||
{
|
||||
radio.openWritingPipe(pipes[0]);
|
||||
radio.openReadingPipe(1,pipes[1]);
|
||||
}
|
||||
else
|
||||
{
|
||||
radio.openWritingPipe(pipes[1]);
|
||||
radio.openReadingPipe(1,pipes[0]);
|
||||
}
|
||||
radio.setChannel(2);
|
||||
radio.setPayloadSize(4);
|
||||
radio.setAutoAck(false);
|
||||
radio.setCRCLength(RF24_CRC_8);
|
||||
radio.openReadingPipe(1,0xE7E7E7E7E7LL);
|
||||
|
||||
//
|
||||
// Start listening
|
||||
|
@ -130,91 +86,56 @@ void setup(void)
|
|||
radio.printDetails();
|
||||
}
|
||||
|
||||
//
|
||||
// Loop
|
||||
//
|
||||
|
||||
void loop(void)
|
||||
{
|
||||
//
|
||||
// Ping out role. Repeatedly send the current time
|
||||
// Receive each packet, dump it out
|
||||
//
|
||||
|
||||
if (role == role_ping_out)
|
||||
{
|
||||
// First, stop listening so we can talk.
|
||||
radio.stopListening();
|
||||
|
||||
// Take the time, and send it. This will block until complete
|
||||
unsigned long time = millis();
|
||||
printf("Now sending %lu...",time);
|
||||
bool ok = radio.write( &time, sizeof(unsigned long) );
|
||||
|
||||
if (ok)
|
||||
printf("ok...");
|
||||
else
|
||||
printf("failed.\n\r");
|
||||
|
||||
// Now, continue listening
|
||||
radio.startListening();
|
||||
|
||||
// Wait here until we get a response, or timeout (250ms)
|
||||
unsigned long started_waiting_at = millis();
|
||||
bool timeout = false;
|
||||
while ( ! radio.available() && ! timeout )
|
||||
if (millis() - started_waiting_at > 200 )
|
||||
timeout = true;
|
||||
|
||||
// Describe the results
|
||||
if ( timeout )
|
||||
{
|
||||
printf("Failed, response timed out.\n\r");
|
||||
}
|
||||
else
|
||||
{
|
||||
// Grab the response, compare, and send to debugging spew
|
||||
unsigned long got_time;
|
||||
radio.read( &got_time, sizeof(unsigned long) );
|
||||
|
||||
// Spew it
|
||||
printf("Got response %lu, round-trip delay: %lu\n\r",got_time,millis()-got_time);
|
||||
}
|
||||
|
||||
// Try again 1s later
|
||||
delay(1000);
|
||||
}
|
||||
|
||||
//
|
||||
// Pong back role. Receive each packet, dump it out, and send it back
|
||||
//
|
||||
|
||||
if ( role == role_pong_back )
|
||||
{
|
||||
// if there is data ready
|
||||
if ( radio.available() )
|
||||
{
|
||||
// Dump the payloads until we've gotten everything
|
||||
unsigned long got_time;
|
||||
bool done = false;
|
||||
while (!done)
|
||||
// Get the packet from the radio
|
||||
payload_t payload;
|
||||
radio.read( &payload, sizeof(payload) );
|
||||
|
||||
// Print the ID of this message. Note that the message
|
||||
// is sent 'big-endian', so we have to flip it.
|
||||
printf("#%05u Buttons ",flip_endian(payload.id));
|
||||
|
||||
// Print the name of each button
|
||||
int i = num_buttons;
|
||||
while (i--)
|
||||
{
|
||||
// Fetch the payload, and see if this was the last one.
|
||||
done = radio.read( &got_time, sizeof(unsigned long) );
|
||||
|
||||
// Spew it
|
||||
printf("Got payload %lu...",got_time);
|
||||
|
||||
// Delay just a little bit to let the other unit
|
||||
// make the transition to receiver
|
||||
delay(20);
|
||||
if ( ! ( payload.buttons & _BV(i) ) )
|
||||
{
|
||||
printf("%s ",button_names[i]);
|
||||
}
|
||||
}
|
||||
|
||||
// First, stop listening so we can talk
|
||||
radio.stopListening();
|
||||
// If no buttons, print None
|
||||
if ( payload.buttons == _BV(num_buttons) - 1 )
|
||||
printf("None");
|
||||
|
||||
// Send the final one back.
|
||||
radio.write( &got_time, sizeof(unsigned long) );
|
||||
printf("Sent response.\n\r");
|
||||
|
||||
// Now, resume listening so we catch the next packets.
|
||||
radio.startListening();
|
||||
printf("\r\n");
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
//
|
||||
// Helper functions
|
||||
//
|
||||
|
||||
// Change a big-endian word into a little-endian
|
||||
uint16_t flip_endian(uint16_t in)
|
||||
{
|
||||
uint16_t low = in >> 8;
|
||||
uint16_t high = in << 8;
|
||||
|
||||
return high | low;
|
||||
}
|
||||
|
||||
// vim:cin:ai:sts=2 sw=2 ft=cpp
|
||||
|
|
Loading…
Reference in New Issue