lightmeter/lightmeter.ino

1671 lines
57 KiB
Arduino
Raw Normal View History

2018-03-22 07:57:53 +00:00
//STM32F103C, 64k flash
//upload method: serial (A9 to RX, A10 to TX)
//To upload set Boot0 jumper to 1 (the one further away from reset btn) and press reset (stm will boot from flash wich contains uart to flash uploader)
//upload via arduino IDE
//To boot program after restart set Boot0 jumper to 0
//Letters 5x7 at Size 1
#include <math.h>
2018-03-22 07:57:53 +00:00
//#include <SPI.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h> // http://www.instructables.com/id/Monochrome-096-i2c-OLED-display-with-arduino-SSD13/
//128 x 64 px
2018-03-26 15:55:17 +00:00
#define WIDTH 128
#define HEIGHT 64
2018-04-14 11:56:49 +00:00
#include <EEPROM.h>
2018-03-22 07:57:53 +00:00
#include <BH1750.h> //from: https://github.com/mysensors/MySensorsArduinoExamples/tree/master/libraries/BH1750
BH1750 lightMeter;
2018-04-14 11:56:49 +00:00
#define INCIDENT_CORRECTION_FACTOR 1.17
//with 1125 25 225 2465 120
//wihtout 1335 32 265 2865 145
/*1,186666667
1,28
1,177777778
1,162271805
1,208333333*/
2018-03-22 07:57:53 +00:00
#define PIN_LDR 0 //A0
#define PIN_BRIGHTMODE 1 //A1
#define PIN_VBAT 2 //A2
2018-04-14 11:56:49 +00:00
#define PIN_LED 8 //White status led A8
2018-03-22 07:57:53 +00:00
#define PIN_TRIGGER PB8
#define PIN_BTNLEFT PA15
#define PIN_BTNCENTER PB4
#define PIN_BTNRIGHT PB5
2018-04-14 11:56:49 +00:00
#define PIN_ON PB9 //pin for hardware latch
2018-03-22 07:57:53 +00:00
#define TIME_AUTOPOWEROFF 120000
2018-04-14 11:56:49 +00:00
#define TIME_METERINGMODESELECTION_CLOSE 60000
#define TIME_METERINGMODESELECTION_SHUTDOWN_SHORTCUT 500
2018-04-14 11:56:49 +00:00
#define LDRDELAY 100 //delay between ldr switches. New analog_high or low reading after that time. Transistor for lower value pulldown resistor switches in between
#define LDRFILTERDELAY 1 //delay in ms between readings sequent readings for smoothing . LDRFILTERDELAY*64 > LDRDELAY
#define LDRSWITCHDELAY 30 //time to wait after transistor switched
#define INCIDENTDELAY 100 //minimum delay between incident sensor (BH1750) readings
#define DEBOUNCETIME 20 //time to not check for inputs after key press
#define BUTTONTIMEHOLD 750 //time for button hold
#define BUTTONTIMEHOLDLONG 3000 //time for button long hold
2018-03-22 07:57:53 +00:00
2018-04-14 11:56:49 +00:00
#define VOLTAGE_WARN 3.4 //voltage per cell //TODO implement warning
2018-03-22 07:57:53 +00:00
//float shuttertimes1[]={1,1.0/2, 1.0/4, 1.0/8, 1.0/15, 1.0/30, 1.0/60, 1.0/125, 1.0/250, 1.0/500, 1.0/1000, 1.0/2000, 1.0/4000, 1.0/8000};
float shuttertimes1[]={64,32,16,8,4,2,1,1.0/2, 1.0/4, 1.0/8, 1.0/15, 1.0/30, 1.0/60, 1.0/125, 1.0/250, 1.0/500, 1.0/1000, 1.0/2000, 1.0/4000, 1.0/8000};
#define SHUTTERTIMES1_MAXINDEX 19
float shuttertimes2[]={30,25,20,15,13,10,8,6,5,4,3.2,2.5,2,1.6,1.3,1,0.8,0.6,0.5,0.4,0.3,1.0/4,1.0/5,1.0/6,1.0/8,1.0/10,1.0/13,1.0/15,1.0/20,1.0/25,1.0/30,1.0/40,1.0/50,1.0/60,1.0/80,1.0/100,1.0/125,1.0/160,1.0/200,1.0/250,1.0/320,1.0/400,1.0/500,1.0/640,1.0/800,1.0/1000,1.0/1250,1.0/1600,1.0/2000,1.0/2500,1.0/3200,1.0/4000};
#define SHUTTERTIMES2_MAXINDEX 51
float shuttertimes3[]={3600,2400,1800,1200,900,600,420,300,210,150,100,60,45,30,20,16,10,8,6,4,3,2,1.5,1,0.5,0.25,0.125,1.0/16};
#define SHUTTERTIMES3_MAXINDEX 27
String settingsnameShutterSelectionMode[]={"Analog","Digital","Pinhole"}; //names for tables
#define MAXIMUM_SHUTTERSELECTIONMODES 3
//Aperature numbers https://en.wikipedia.org/wiki/F-number
float aperaturesFull[]={1,1.4, 2, 2.8, 4, 5.6, 8, 11, 16, 22, 32,45};
#define APERATURESFULL_MAXINDEX 11
float aperaturesHalf[]={1, 1.2, 1.4, 1.7, 2, 2.4, 2.8, 3.4, 4, 4.8, 5.6, 6.7, 8, 9.5, 11, 13, 16, 19, 22, 27 ,32, 38, 45};
#define APERATURESHALF_MAXINDEX 22
2018-03-22 07:57:53 +00:00
float aperaturesThird[]={1, 1.1, 1.2, 1.4, 1.6, 1.8, 2, 2.2, 2.5, 2.8, 3.2, 3.5, 4, 4.5, 5.0, 5.6, 6.3, 7.1, 8, 9, 10, 11, 13, 14, 16, 18, 20, 22, 25, 29, 32, 36, 40, 45};
#define APERATURESTHIRD_MAXINDEX 33
2018-03-22 07:57:53 +00:00
String settingsnameAperatureSelectionMode[]={"Full","Half","Third"}; //names for tables
#define MAXIMUM_APERATURESELECTIONMODES 3
float isoFull[]={0.78,1.56,3.13,6.25,12.5,25,50,100,200,400,800,1600,3200,6400,12500,25600};
uint8_t isoFullDIN[]={0,3, 6, 9, 12, 15,18,21 ,24 ,27 ,30 ,33 ,36 ,39 ,42 ,45};
float isoThird[]={0.78,0.98,1.24,1.56,1.97,2.48,3.13,3.93,4.96,6.25,7.87,9.92,12.5,16,20,25,32,40,50,64,80,100,125,160,200,250,320,400,500,640,800,1000,1250,1600,2000,2500,3200,4000,5000,6400,8000,10000,12500,16000,20000,25600};
uint8_t isoThirdDIN[]={0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20, 21, 22 ,23 ,24 ,25 ,26 ,27 ,28 ,29 ,30 ,31 ,32 ,33 ,34 ,35 ,36 ,37 ,38 ,39 ,40 ,41 ,42 ,43 ,44 ,56};
2018-03-22 07:57:53 +00:00
long loopmillis=0; //only use one millis reading each loop
long last_ldrReading=0;
2018-04-14 11:56:49 +00:00
long last_ldrReadingFilter=0;
long last_incidentReading=0;
2018-03-22 07:57:53 +00:00
long millis_lastchange=0;
long millis_lastinput=0;
2018-04-14 11:56:49 +00:00
long millis_ledoff=0; //for led blink
long millis_opened_meteringmodeselection=0; //time when meteringmodeselecten was opened (for led flashlight timing)
#define DELAY_METERINGMODESELECTION_FLASHLIGHT 2000
2018-03-22 07:57:53 +00:00
2018-03-26 15:55:17 +00:00
2018-03-22 07:57:53 +00:00
long timebuttonpressed_trigger;
long timebuttonpressed_left;
long timebuttonpressed_center;
long timebuttonpressed_right;
//Short press (true when button short pressed, on release)
boolean button_trigger=false;
boolean button_left=false;
boolean button_center=false;
boolean button_right=false;
//long press (true when button is held down for BUTTONTIMEHOLD, on time elapsed)
boolean button_hold_trigger=false;
boolean button_hold_left=false;
boolean button_hold_center=false;
boolean button_hold_right=false;
//even longer press
boolean button_hold_long_trigger=false;
long timebuttonpressed_trigger_long=0;
float vbat=100;
2018-03-22 07:57:53 +00:00
struct Settings {
uint8_t minimumAperatureIndex; //see corresponding aperatures table
uint8_t aperatureSelectionMode; //1=Full, 2=Half, 3=Third
uint8_t shutterSelectionMode; //index for which shuttertimes table to use
uint8_t ISOSelectionMode; //1=Full, 2=Thirds
uint8_t manualev_moveamount_frac; // 1=1ev, 2=1/2ev, 3=1/3 ev
2018-03-22 07:57:53 +00:00
};
#define MAXIMUM_MANUAL_EV_MOVEAMOUNT_FRAC 3
2018-03-22 07:57:53 +00:00
2018-04-14 11:56:49 +00:00
bool settingsStructEqual(Settings a, Settings b){
if (a.minimumAperatureIndex!=b.minimumAperatureIndex || a.aperatureSelectionMode!=b.aperatureSelectionMode || a.shutterSelectionMode!=b.shutterSelectionMode || a.ISOSelectionMode!=b.ISOSelectionMode){
return false;
}
return true;
}
Settings userSettings= {1,1, 1,2,1};
2018-04-14 11:56:49 +00:00
Settings eeprom_userSettings; //to store current eeprom status
2018-03-22 07:57:53 +00:00
#define OLED_RESET 4
Adafruit_SSD1306 display(OLED_RESET);
2018-04-14 11:56:49 +00:00
uint16_t incident=0; //incident reading from bh1750
2018-03-22 07:57:53 +00:00
uint16_t analog_low=0; //better for low light
uint16_t analog_high=0; //better for bright light (higher pulldown resistor for ldr)
2018-04-14 11:56:49 +00:00
uint16_t analog_reading_filtering=0;
uint8_t analog_reading_count=0;
2018-03-22 07:57:53 +00:00
float ev=0; //calculated EV from LDR readings (reflected) or from Luxmeter (incident)
float ev_min=-255,ev_max=-255,ev_last=-255;
2018-03-22 07:57:53 +00:00
float showAperature=0;
float showShutter=0;
bool manualev_mode=false; //manual ev change by left/right
2018-03-22 07:57:53 +00:00
//Usersettings
float setAperature=8; //set to use aperature. 0 for auto
float setShutter=0; //set to use shutter time, 0 for auto
float setISO=100; //set to ISO
2018-03-22 07:57:53 +00:00
2018-04-14 11:56:49 +00:00
float eeprom_setAperature=0; //set to use aperature. 0 for auto
float eeprom_setShutter=0; //set to use shutter time, 0 for auto
2018-05-03 14:00:40 +00:00
float eeprom_setISO=0; //set to ISO
2018-04-14 11:56:49 +00:00
#define EEPROMADDRESS_APERATURE 0x801F000 //float = 32bit = 4byte
#define EEPROMADDRESS_SHUTTER 0x801F004 //float = 32bit = 4byte
2018-05-03 14:00:40 +00:00
#define EEPROMADDRESS_ISO 0x801F008 //float 32bit = 4byte
#define EEPROMADDRESS_METERINGMODE 0x801F00C //uint8_t 1byte
#define EEPROMADDRESS_USERSETTINGS 0x801F00D //Settings struct
2018-04-14 11:56:49 +00:00
2018-03-22 07:57:53 +00:00
enum displaymode {
lightmeter,
2018-03-26 15:55:17 +00:00
settings,
meteringmodeselection
2018-03-22 07:57:53 +00:00
};
displaymode displaymode=lightmeter;
uint8_t settings_selectedItem=0; //in settings display
String settingStrings[]={"ISO:","F-Stops:","Timetable:","EV Step:","Turn Off"};
#define SETTINGS_SELECTEDITEM_MAX 4 //inclusive. 2 means 3 items available
2018-03-22 07:57:53 +00:00
boolean settings_itemActive=false; //item in settings selected to change value
2018-04-14 11:56:49 +00:00
#define DISPLAY_UPDATEDELAY 200
long last_displayupdate=0;
2018-03-22 07:57:53 +00:00
#define METERINGMODE_REFLECTIVE 0
#define METERINGMODE_INCIDENT 1
uint8_t meteringmode=METERINGMODE_REFLECTIVE;
2018-04-14 11:56:49 +00:00
uint8_t eeprom_meteringmode=0;
2018-04-14 11:56:49 +00:00
bool eeprom_red=false; //false, if eeprom need to be red
2018-03-22 07:57:53 +00:00
2018-03-26 15:55:17 +00:00
2018-04-14 11:56:49 +00:00
bool debug_printreadings=false;
uint16_t debug_analog_high=0;
uint16_t debug_analog_low=0;
2018-03-26 15:55:17 +00:00
2018-03-22 07:57:53 +00:00
char tempstring[16]; //for dtostrf //dtostrf(modefactor,1,3,tempstring);
#if (SSD1306_LCDHEIGHT != 64)
#error("Height incorrect, please fix Adafruit_SSD1306.h!");
#endif
2018-03-26 15:55:17 +00:00
//Icons. Exported as .xbm from gimp and renamed to .c
#include "icon_incident.c"
#include "icon_spot.c"
2018-03-26 15:55:17 +00:00
#include "icon_arrow.c"
#include "icon_one_third.c"
#include "icon_one_half.c"
#include "icon_two_third.c"
2018-03-26 15:55:17 +00:00
void setup() {
2018-04-14 11:56:49 +00:00
Serial.begin(115200);
2018-03-22 07:57:53 +00:00
Serial.println("Started");
Serial.println("Init Display");
2018-03-22 07:57:53 +00:00
display.begin(SSD1306_SWITCHCAPVCC, 0x3C);
display.clearDisplay();
display.display();
Serial.println("Init BH1750");
lightMeter.begin(BH1750_CONTINUOUS_HIGH_RES_MODE_2); //max reading=54612
2018-03-22 07:57:53 +00:00
//set measurement time (for higher resolution) http://www.raspberry-pi-geek.de/Magazin/2015/04/Digital-Light-Sensor-BH1750-am-Raspberry-Pi
//lightMeter.write8(71); //01000111 //high bit: 01000xxx bits 7,6,5
//lightMeter.write8(126); //01111110 //log bit: 011xxxxx bits 4,3,2,1,0
pinMode(PIN_LDR, INPUT_ANALOG);
pinMode(PIN_VBAT, INPUT_ANALOG);
pinMode(PIN_TRIGGER, INPUT_PULLUP);
pinMode(PIN_BTNLEFT, INPUT_PULLUP);
pinMode(PIN_BTNCENTER, INPUT_PULLUP);
pinMode(PIN_BTNRIGHT, INPUT_PULLUP);
pinMode(PIN_BRIGHTMODE, OUTPUT);
digitalWrite(PIN_BRIGHTMODE, LOW);
pinMode(PIN_ON, OUTPUT);
digitalWrite(PIN_ON, HIGH);
2018-04-14 11:56:49 +00:00
pinMode(PIN_LED, OUTPUT);
analogWrite(PIN_LED,255); //blink led on
2018-04-14 11:56:49 +00:00
delay(50);
analogWrite(PIN_LED,0); //LED OFF //blink led off
2018-03-22 07:57:53 +00:00
millis_lastchange=millis();
Serial.println("Initialized");
2018-04-14 11:56:49 +00:00
if (!digitalRead(PIN_TRIGGER)){ //hold trigger button during power on activates serial debug printing
debug_printreadings=true;
}
2018-03-22 07:57:53 +00:00
2018-03-22 07:57:53 +00:00
}
2018-04-14 11:56:49 +00:00
bool saveSettingsToEEPROM(bool force){
bool _eepromwritten=false;
//checks and writes changes to eeprom
if (eeprom_setAperature!=setAperature || force){ //value change or write forced
EEPROM_writeAnything(EEPROMADDRESS_APERATURE, setAperature);
_eepromwritten=true;
}
if (eeprom_setShutter!=setShutter || force){ //value change or write forced
EEPROM_writeAnything(EEPROMADDRESS_SHUTTER, setShutter);
_eepromwritten=true;
}
if (eeprom_setISO!=setISO || force){ //value change or write forced
EEPROM_writeAnything(EEPROMADDRESS_ISO, setISO);
_eepromwritten=true;
}
if (eeprom_meteringmode!=meteringmode || force){ //one of the values change or write forced
EEPROM_writeAnything(EEPROMADDRESS_METERINGMODE, meteringmode);
_eepromwritten=true;
}
if (!settingsStructEqual(eeprom_userSettings,userSettings) || force){ //one of the values change or write forced
EEPROM_writeAnything(EEPROMADDRESS_USERSETTINGS, userSettings);
_eepromwritten=true;
}
return _eepromwritten;
}
2018-03-22 07:57:53 +00:00
void loop() {
loopmillis=millis(); //read millis for this cycle
2018-04-14 11:56:49 +00:00
if (!eeprom_red){ //only executed one time
eeprom_red=true;
readEEPROM();
}
2018-03-22 07:57:53 +00:00
handleInputs();
2018-03-26 15:55:17 +00:00
calculateFromEV();
2018-03-22 07:57:53 +00:00
updateDisplay();
2018-04-14 11:56:49 +00:00
checkLED();
}
void readEEPROM(){
2018-03-22 07:57:53 +00:00
2018-04-14 11:56:49 +00:00
if (!digitalRead(PIN_BTNLEFT) && !digitalRead(PIN_BTNCENTER) && !digitalRead(PIN_BTNRIGHT) ){ //push all front buttons (left, center, right) to restore default settings
analogWrite(PIN_LED,255);
2018-04-14 11:56:49 +00:00
delay(1000); //1s led on confirmation
analogWrite(PIN_LED,0); //LED OFF
2018-04-14 11:56:49 +00:00
saveSettingsToEEPROM(true); //force writing. userSettings contains the default values at this point
delay(200);
analogWrite(PIN_LED,255);
2018-04-14 11:56:49 +00:00
delay(200); //1s led on confirmation
analogWrite(PIN_LED,0); //LED OFF
2018-04-14 11:56:49 +00:00
delay(200);
analogWrite(PIN_LED,255);
2018-04-14 11:56:49 +00:00
delay(200); //1s led on confirmation
analogWrite(PIN_LED,0); //LED OFF
2018-04-14 11:56:49 +00:00
delay(1000);
}
2018-03-22 07:57:53 +00:00
2018-04-14 11:56:49 +00:00
//read current eeprom
EEPROM_readAnything(EEPROMADDRESS_APERATURE, eeprom_setAperature);
EEPROM_readAnything(EEPROMADDRESS_SHUTTER, eeprom_setShutter);
EEPROM_readAnything(EEPROMADDRESS_ISO, eeprom_setISO);
EEPROM_readAnything(EEPROMADDRESS_METERINGMODE, eeprom_meteringmode);
EEPROM_readAnything(EEPROMADDRESS_USERSETTINGS, eeprom_userSettings);
Serial.println("");
Serial.println("EEPROM eeprom settings");
Serial.println(eeprom_setAperature);
Serial.println(eeprom_setShutter);
Serial.println(eeprom_setISO);
Serial.println("EEPROM eeprom_userSettings");
Serial.println(eeprom_userSettings.minimumAperatureIndex);
Serial.println(eeprom_userSettings.aperatureSelectionMode);
Serial.println(eeprom_userSettings.shutterSelectionMode);
Serial.println(eeprom_userSettings.ISOSelectionMode);
Serial.println("");
if (eeprom_userSettings.minimumAperatureIndex==255){ //after flashing eeprom contains FF.., check one value
for (int i=0;i<10;i++){ //blink a few times to show that eeprom was clean
delay(50);
analogWrite(PIN_LED,255);
2018-04-14 11:56:49 +00:00
delay(50); //1s led on confirmation
analogWrite(PIN_LED,0);
2018-04-14 11:56:49 +00:00
}
}else{ //
//apply
setAperature=eeprom_setAperature;
setShutter=eeprom_setShutter;
setISO=eeprom_setISO;
meteringmode=eeprom_meteringmode;
userSettings=eeprom_userSettings;
}
2018-03-22 07:57:53 +00:00
}
2018-04-14 11:56:49 +00:00
2018-03-22 07:57:53 +00:00
void handleInputs()
{
//Short press (true when button short pressed, on release)
button_trigger=false;
button_left=false;
button_center=false;
button_right=false;
//long press (true when button is held down for BUTTONTIMEHOLD, on time elapsed)
button_hold_trigger=false;
button_hold_left=false;
button_hold_center=false;
button_hold_right=false;
//even longer press
button_hold_long_trigger=false;
2018-03-22 07:57:53 +00:00
if (millis()-millis_lastinput>DEBOUNCETIME) //Button debouncing
{
//Trigger
if (timebuttonpressed_trigger == 0 && !digitalRead(PIN_TRIGGER)){ //first time pressed down. (low when pressed)
timebuttonpressed_trigger=loopmillis; //set time of button press
timebuttonpressed_trigger_long=loopmillis; //set time of button press, for long hold timing
2018-03-22 07:57:53 +00:00
}else if(timebuttonpressed_trigger != 0 && digitalRead(PIN_TRIGGER)){ //button released (was pressed)
if (loopmillis-timebuttonpressed_trigger < BUTTONTIMEHOLD){ //short press
button_trigger=true;
}
timebuttonpressed_trigger=0; //re-enable after short press and release from hold
}else if(loopmillis-timebuttonpressed_trigger >= BUTTONTIMEHOLD && timebuttonpressed_trigger>0){ //held down long enough and not already hold triggered
button_hold_trigger=true;
timebuttonpressed_trigger=-1; //-1 as flag for hold triggered
}
if (timebuttonpressed_trigger_long>0 && loopmillis-timebuttonpressed_trigger_long >= BUTTONTIMEHOLDLONG && !digitalRead(PIN_TRIGGER)) { //button held down even longer, set hold long flag for as long as button is down
button_hold_long_trigger=true;
}else if(timebuttonpressed_trigger_long>0 && digitalRead(PIN_TRIGGER)){ //released
timebuttonpressed_trigger_long=0; //reset long hold timing
}
2018-03-22 07:57:53 +00:00
//Left
if (timebuttonpressed_left == 0 && !digitalRead(PIN_BTNLEFT)){ //first time pressed down. (low when pressed)
timebuttonpressed_left=loopmillis; //set time of button press
}else if(timebuttonpressed_left != 0 && digitalRead(PIN_BTNLEFT)){ //button released (was pressed)
if (loopmillis-timebuttonpressed_left < BUTTONTIMEHOLD){ //short press
button_left=true;
}
timebuttonpressed_left=0; //re-enable after short press and release from hold
}else if(loopmillis-timebuttonpressed_left >= BUTTONTIMEHOLD && timebuttonpressed_left>0){ //held down long enough and not already hold triggered
button_hold_left=true;
timebuttonpressed_left=-1; //-1 as flag for hold triggered
}
//Center
if (timebuttonpressed_center == 0 && !digitalRead(PIN_BTNCENTER)){ //first time pressed down. (low when pressed)
timebuttonpressed_center=loopmillis; //set time of button press
}else if(timebuttonpressed_center != 0 && digitalRead(PIN_BTNCENTER)){ //button released (was pressed)
if (loopmillis-timebuttonpressed_center < BUTTONTIMEHOLD){ //short press
button_center=true;
}
timebuttonpressed_center=0; //re-enable after short press and release from hold
}else if(loopmillis-timebuttonpressed_center >= BUTTONTIMEHOLD && timebuttonpressed_center>0){ //held down long enough and not already hold triggered
button_hold_center=true;
timebuttonpressed_center=-1; //-1 as flag for hold triggered
}
//Right
if (timebuttonpressed_right == 0 && !digitalRead(PIN_BTNRIGHT)){ //first time pressed down. (low when pressed)
timebuttonpressed_right=loopmillis; //set time of button press
}else if(timebuttonpressed_right != 0 && digitalRead(PIN_BTNRIGHT)){ //button released (was pressed)
if (loopmillis-timebuttonpressed_right < BUTTONTIMEHOLD){ //short press
button_right=true;
}
timebuttonpressed_right=0; //re-enable after short press and release from hold
}else if(loopmillis-timebuttonpressed_right >= BUTTONTIMEHOLD && timebuttonpressed_right>0){ //held down long enough and not already hold triggered
button_hold_right=true;
timebuttonpressed_right=-1; //-1 as flag for hold triggered
}
}
/*
if (button_trigger || button_left || button_center || button_right){
Serial.println("Buttons short:");
Serial.print(button_trigger);
Serial.print(button_left);
Serial.print(button_center);
Serial.println(button_right);
}
if (button_hold_trigger || button_hold_left || button_hold_center || button_hold_right){
Serial.println("Buttons long:");
Serial.print(button_hold_trigger);
Serial.print(button_hold_left);
Serial.print(button_hold_center);
Serial.println(button_hold_right);
}
*/
//Voltage
float _vbat=map(analogRead(PIN_VBAT), 0,3560,0,8200)/1000.0; //180k and 300k voltage divider. 8,4V -> 3,15V=3910
if (_vbat<vbat){
vbat=_vbat; //voltage can only decrease
}
2018-03-22 07:57:53 +00:00
//LDR
2018-04-14 11:56:49 +00:00
if ( loopmillis-last_ldrReadingFilter>LDRFILTERDELAY && loopmillis-last_ldrReading>LDRSWITCHDELAY) //multiple successive reading for filtering. each LDRFILTERDELAY ms and wait LDRSWITCHDELAY for first reading
{
analog_reading_filtering+=analogRead(PIN_LDR);
analog_reading_count++;
last_ldrReadingFilter=loopmillis;
}
if ( loopmillis-last_ldrReading>LDRDELAY ) //time over for one reading (low or high)
2018-03-22 07:57:53 +00:00
{
if (!digitalRead(PIN_BRIGHTMODE)){
2018-04-14 11:56:49 +00:00
analog_low=analog_reading_filtering/analog_reading_count;
2018-03-22 07:57:53 +00:00
}else{
2018-04-14 11:56:49 +00:00
analog_high=analog_reading_filtering/analog_reading_count;
if (debug_printreadings){
Serial.print(analog_low);//for calibration output
Serial.print(";");
Serial.println(analog_high);
}
2018-03-22 07:57:53 +00:00
}
2018-04-14 11:56:49 +00:00
/*Serial.print(analog_reading_count);
Serial.print(" value=");
Serial.println(analog_reading_filtering);*/
analog_reading_count=0; //reset
analog_reading_filtering=0; //reset
2018-03-22 07:57:53 +00:00
digitalWrite(PIN_BRIGHTMODE, !digitalRead(PIN_BRIGHTMODE)); //switch modes
last_ldrReading=loopmillis;
}
//Lightsensor BH1750
if ( loopmillis-last_incidentReading>INCIDENTDELAY )
{
incident = lightMeter.readLightLevel(); //value in lux from sensor
last_incidentReading=loopmillis;
}
2018-03-22 07:57:53 +00:00
//Test asdf
/*
if ( !digitalRead(PIN_TRIGGER) ) {
Serial.println("roundAperature");
for (float i=0.1;i<30;i+=0.5){
Serial.print(i);
Serial.print(" -> ");
Serial.println(roundAperature(i,1));
}
Serial.println("roundShutter");
for (float i=1.0/8000;i<32;i*=2){
Serial.print(i,6);
Serial.print(" -> ");
Serial.print(roundShutter(i,2),6);
2018-03-22 07:57:53 +00:00
Serial.print(" -- ");
Serial.println(reciprocFloat(roundShutter(i,2)));
}
2018-03-22 07:57:53 +00:00
}
2018-03-22 07:57:53 +00:00
Serial.println("calculateShutter at iso 100 f2.8");
for (float i=-2;i<18;i+=0.25){
2018-03-22 07:57:53 +00:00
Serial.print(i);
Serial.print(" -> ");
float test_calcshutter=calculateShutter(i, (uint16_t)100, 2.8);
//Serial.println(test_calcshutter,6);
float test_showShutter=roundShutter(test_calcshutter,2);
Serial.print("rounded Shutter from "); Serial.print(test_calcshutter,6); Serial.print(" to "); Serial.println(test_showShutter,6); //asdf
if (test_showShutter>0.25) //check shuttertime
{ //show full seconds
Serial.print("int=");
Serial.print(int(test_showShutter));
if (test_showShutter-int(test_showShutter)>0){ //has decimals
Serial.print(" ,");
Serial.print((int)round( (test_showShutter-int(test_showShutter))*10)); //show one decimal
}
Serial.println("");
}else{ //show fraction of a second
Serial.print("frac= 1/");
int _frac_showShutter = (int) ( (1.0f/( (int)(test_showShutter*1000000) ) )*1000000 );
Serial.print( _frac_showShutter );
Serial.println("");
}
2018-03-22 07:57:53 +00:00
}
Serial.println("calculateAperature at iso 100 1/250s");
for (float i=-2;i<18;i+=0.25){
2018-03-22 07:57:53 +00:00
Serial.print(i);
Serial.print(" -> ");
Serial.println(calculateAperature(i, (uint16_t)100, 1.0/250),6);
2018-03-22 07:57:53 +00:00
}
}*/
2018-03-22 07:57:53 +00:00
switch(displaymode){
case lightmeter:
handleInputs_Lightmeter();
break;
case settings:
handleInputs_Settings();
break;
2018-03-26 15:55:17 +00:00
case meteringmodeselection:
handleInputs_Meteringmodeselection();
break;
2018-03-22 07:57:53 +00:00
}
if (millis()-millis_lastchange>TIME_AUTOPOWEROFF){
2018-04-14 11:56:49 +00:00
poweroff();
2018-03-22 07:57:53 +00:00
}
if ( button_trigger || button_left || button_center || button_right ) {
2018-03-26 15:55:17 +00:00
millis_lastchange=millis(); //for auto poweroff and auto closes
2018-03-22 07:57:53 +00:00
millis_lastinput=millis(); //for debouncing
}
}
2018-04-14 11:56:49 +00:00
void poweroff(){
bool _eepromwritten=saveSettingsToEEPROM(false); //save only changes to eeprom
analogWrite(PIN_LED,255); //Blink led
2018-04-14 11:56:49 +00:00
delay(100);
analogWrite(PIN_LED,0);
2018-04-14 11:56:49 +00:00
if (_eepromwritten){
delay(100);
analogWrite(PIN_LED,255);
2018-04-14 11:56:49 +00:00
delay(100);
analogWrite(PIN_LED,0);
2018-04-14 11:56:49 +00:00
}
digitalWrite(PIN_ON, LOW); //Turn off hardware latch
}
2018-03-22 07:57:53 +00:00
void handleInputs_Lightmeter()
{
2018-03-26 15:55:17 +00:00
if ( button_center ) { //open meteringmode selection
displaymode=meteringmodeselection;
2018-04-14 11:56:49 +00:00
millis_opened_meteringmodeselection=loopmillis;
2018-03-26 15:55:17 +00:00
}
2018-03-22 07:57:53 +00:00
if ( button_hold_center ) { //Go to Settings
displaymode=settings;
}
2018-03-26 15:55:17 +00:00
2018-03-22 07:57:53 +00:00
if (manualev_mode){ //Manual Ev
2018-03-22 07:57:53 +00:00
//Value Change
if ( button_left ) {
ev-=1.0/userSettings.manualev_moveamount_frac;
2018-03-22 07:57:53 +00:00
}
if ( button_right ) {
ev+=1.0/userSettings.manualev_moveamount_frac;
2018-03-22 07:57:53 +00:00
}
//Change Mode
if ( button_hold_left ){ // Manual Ev -> Av
2018-03-22 07:57:53 +00:00
setAperature=showAperature;
setShutter=0;
manualev_mode=false;
}
if ( button_hold_right ){ // Manual Ev -> T
setShutter=showShutter;
setAperature=0;
manualev_mode=false;
2018-03-22 07:57:53 +00:00
}
}else if(setShutter==0){ //Aperature Priority
manualev_mode=false;
2018-03-22 07:57:53 +00:00
//Value Change
if ( button_left ) {
changeAperature(1); //Decrement Aperature
}
if ( button_right ) {
changeAperature(-1); //Increment Aperature
}
//Change Mode
if ( button_hold_left ){ //Av -> Manual Ev
manualev_mode=true;
2018-03-22 07:57:53 +00:00
}
if ( button_hold_right ){ //Av -> T
setShutter=showShutter;
setAperature=0;
}
}else if (setAperature==0){ //Shutter Priority
manualev_mode=false;
2018-03-22 07:57:53 +00:00
//Value Change
if ( button_left ) {
changeShutter(1); //Decrement Aperature
}
if ( button_right ) {
changeShutter(-1); //Increment Aperature
}
//Change Mode
if ( button_hold_left ){ //T -> Av
setAperature=showAperature;
setShutter=0;
}
if ( button_hold_right ){ //T -> Manual Ev
manualev_mode=true;
2018-03-22 07:57:53 +00:00
}
}
if (button_trigger || button_hold_long_trigger) { //Trigger or very long hold
ev_last=ev;
2018-03-26 15:55:17 +00:00
ev=getEV(); //set ev to current measurement by selected mode
if (ev<ev_min || ev_min<-254){ //new ev is smaller than last or ev_min wasn set
ev_min=ev;
}
if(ev>ev_max){ //new ev is greater
ev_max=ev;
}
2018-04-14 11:56:49 +00:00
debug_analog_high=analog_high;
debug_analog_low=analog_low;
//LED Brightness on trigger
uint8_t triggerblinkbrightness=255;
if (ev<4){ //dim led when dark
triggerblinkbrightness=map(ev,2,4,5,255);
}
if (ev<2){
triggerblinkbrightness=5;
}
if (button_hold_long_trigger){ //low brightness on long hold
triggerblinkbrightness=5;
}
blinkLED(20,triggerblinkbrightness);
}
if (button_hold_trigger) { //Trigger hold, resets ev_min,max and last
ev_min=-255; //placeholder for "not set"
ev_max=-255;
ev_last=-255;
//LED Brightness on trigger
uint8_t triggerblinkbrightness=255;
if (ev<4){ //dim led when dark
triggerblinkbrightness=map(ev,4,0,255,50);
}
blinkLED(400,triggerblinkbrightness);
2018-03-26 15:55:17 +00:00
}
2018-03-22 07:57:53 +00:00
}
2018-04-14 11:56:49 +00:00
2018-03-22 07:57:53 +00:00
void handleInputs_Settings()
{
if ( button_hold_center ) { //Go to Lightmeter
settings_itemActive=false; //deselect item
2018-03-22 07:57:53 +00:00
displaymode=lightmeter;
}
if (!settings_itemActive){ //select items
if ( button_left ) {
if (settings_selectedItem>0){ //not first item
settings_selectedItem-=1;
}
}
if ( button_right ) {
if (settings_selectedItem<SETTINGS_SELECTEDITEM_MAX){ //not last item
settings_selectedItem+=1;
}
}
if ( button_center ){
settings_itemActive=true; //select item to change value
}
}else{ //item selected to change value
switch (settings_selectedItem)
{
case 0: //ISO
if ( button_left ) {
changeISO(-1);
}
if ( button_right ) {
changeISO(1);
}
break;
case 1: //Aperature Selection Mode
if ( button_left ) {
if(userSettings.aperatureSelectionMode>1){
userSettings.aperatureSelectionMode-=1;
}
}
if ( button_right ) {
if (userSettings.aperatureSelectionMode<MAXIMUM_APERATURESELECTIONMODES){
userSettings.aperatureSelectionMode+=1;
}
}
break;
case 2: //Shutter Selection Mode
if ( button_left ) {
if(userSettings.shutterSelectionMode>1){
userSettings.shutterSelectionMode-=1;
}
}
if ( button_right ) {
if (userSettings.shutterSelectionMode<MAXIMUM_SHUTTERSELECTIONMODES){
userSettings.shutterSelectionMode+=1;
}
}
break;
case 3: //manual ev moveamount
if ( button_left ) {
if(userSettings.manualev_moveamount_frac>1){
userSettings.manualev_moveamount_frac-=1;
}
}
if ( button_right ) {
if (userSettings.manualev_moveamount_frac<MAXIMUM_MANUAL_EV_MOVEAMOUNT_FRAC){
userSettings.manualev_moveamount_frac+=1;
}
}
break;
case 4: //Turn Off
2018-04-14 11:56:49 +00:00
poweroff();
2018-03-22 07:57:53 +00:00
break;
}
if ( button_center ){
settings_itemActive=false; //return to item selection
}
}
}
2018-03-26 15:55:17 +00:00
void handleInputs_Meteringmodeselection()
{
if ( button_center ) { //next or back to main screen
if (millis()-millis_lastchange<TIME_METERINGMODESELECTION_SHUTDOWN_SHORTCUT) { //double press select (center) to poweroff
poweroff(); //Turn off
}
2018-03-26 15:55:17 +00:00
displaymode=lightmeter;
}
if ( button_left ){
meteringmode = METERINGMODE_REFLECTIVE;
displaymode=lightmeter; // and close
}
if ( button_right ) {
meteringmode = METERINGMODE_INCIDENT;
displaymode=lightmeter; // and close
}
if (millis()-millis_lastchange>TIME_METERINGMODESELECTION_CLOSE){ //Automatic close
displaymode=lightmeter;
}
}
2018-03-22 07:57:53 +00:00
float reciprocFloat(float p){
if (p<1){
return (1.0f/( (int)(p*1000000) ) )*1000000 ;
}else{
return (1/p);
}
}
2018-03-26 15:55:17 +00:00
float getEV(){
float _ev=0;
if (meteringmode == METERINGMODE_REFLECTIVE){ //### SPOT
//ev=map(analog_low,500, 3500 ,500, 1400)/100.0; //for testing
2018-04-14 11:56:49 +00:00
//first prototype.
//double highev=11.7400532 + 0.000216655133*analog_high + 0.00000111372253*pow(analog_high,2) + -0.000000000163800818 *pow(analog_high,3);
//double lowev=-0.763427709 + 0.0138031137*analog_low + -0.00000576990095*pow(analog_low,2) + 0.000000000871611285*pow(analog_low,3);
//calibration 20180413
//polynomial only
//double highev=4.76455098 + 0.00961533698*analog_high - 0.00000399325586*pow(analog_high,2) + 0.000000000654378697 *pow(analog_high,3);
//double lowev=-38.9534785 + 0.310426970*analog_low - 0.000769939297*pow(analog_low,2) + 0.000000639458491*pow(analog_low,3);
double log_low=log(analog_low);
//[-2.47999992e+02 5.59942657e+03 -4.74076773e+04 1.78389539e+05 -2.51728845e+05]
double lowev=-251728.845 + 178389.539*log_low - 47407.6773*pow(log_low,2) + 5599.42657*pow(log_low,3) - 247.999992*pow(log_low,4);
double log_high=log(analog_high);
//[7.27310051e-02 -2.02919373e+00 2.23823220e+01 -1.22121768e+02 3.32574527e+02 -3.60445720e+02]
double highev=-360.445720 + 332.574527*log_high - 122.121768*pow(log_high,2) + 22.3823220*pow(log_high,3) - 2.02919373*pow(log_high,4) + 0.0727310051*pow(log_high,5);
/*Serial.print("analog_low="); //asdf
Serial.print(analog_low);
Serial.print(" log_low=");
Serial.print(log_low);
Serial.print(" lowev=");
Serial.println(lowev);
Serial.print("analog_high=");
Serial.print(analog_high);
Serial.print(" log_high=");
Serial.print(log_high);
Serial.print(" highev=");
Serial.println(highev);*/
2018-04-14 11:56:49 +00:00
if (highev>2){
2018-03-26 15:55:17 +00:00
_ev=highev;
Serial.println("using high ev");
}else if(lowev<1){
2018-03-26 15:55:17 +00:00
_ev=lowev;
Serial.println("using low ev");
}else{ //mix of both
float mix=min(1.0, max(0.0,(lowev-1)/(2-1))); //0 to 1, 0-> use only lowev, 1-> use only highev
2018-03-26 15:55:17 +00:00
_ev=lowev*(1-mix)+highev*mix;
Serial.print("mixing mix=");
Serial.println(mix);
}
Serial.print("EV=");
Serial.println(_ev);
2018-03-26 15:55:17 +00:00
}else if (meteringmode == METERINGMODE_INCIDENT){ //### INCIDENT
2018-04-14 11:56:49 +00:00
_ev = luxToEv(incident*INCIDENT_CORRECTION_FACTOR);
2018-03-22 07:57:53 +00:00
}
2018-03-26 15:55:17 +00:00
return _ev;
}
void calculateFromEV()
{
2018-03-22 07:57:53 +00:00
if (setAperature>0){ //Aperature Priority
showAperature=setAperature; //use user set Aperature
showShutter=calculateShutter(ev,setISO, setAperature);
}else if(setShutter>0){ //Shutter Priority
showShutter=setShutter; //use user set Shutter
showAperature=calculateAperature(ev, setISO, setShutter);
}
}
double evToLux(double ev) {
return pow(2, ev) * 2.5;
}
double luxToEv(uint16_t lux){
if (lux <= 2){
return 0;
}
return log (lux/2.5) / log (2);
}
float calculateShutter(float pEv, uint16_t pIso, float pAperature) //returns calculated Shutter speed given Ev, ISO and Aperature
2018-03-22 07:57:53 +00:00
{
//EV = log2 ( 100* Aperature^2 / (ISO * Time ))
//100* Aperature^2 / (2^EV * ISO) = Time
return (100.0 * pow( pAperature,2) ) / (pow(2,pEv)*pIso);
}
float calculateAperature(float pEv, uint16_t pIso, float pShutter) //returns mathematical aperature in x1
{
//EV = log2 ( 100* Aperature^2 / (ISO * Time ))
// sqrt( 2^EV *(ISO * Time ) /100 ) = Aperature
return sqrt( pow(2,pEv) * pIso * pShutter / 100.0 ) ;
}
float roundShutter(float pShutter, uint8_t pMethod) //round shutter to typical values
{
uint8_t _index=findShutterIndex(pShutter,pMethod);
//use closest shutter value
switch(pMethod){
case 1: //
return shuttertimes1[_index];
break;
case 2: //
return shuttertimes2[_index];
break;
case 3: //
return shuttertimes3[_index];
break;
2018-03-22 07:57:53 +00:00
}
}
float roundAperature(float pAperature, uint8_t pMethod) //round Aperature (x1) to typical values. method=0 -> leave, 1=full stops, 2=half stops, 3=third stops
{
if (pMethod==0){
return pAperature;
}
uint8_t closest_index=findAperatureIndex(pAperature,pMethod);
//use closest aperature value
switch(pMethod){
case 1: //full stops
return aperaturesFull[closest_index];
break;
case 2: //half stops
//return float ( pow(sqrt(sqrt(2)), _index-2) );
return aperaturesHalf[closest_index];
break;
case 3: //third stops
return aperaturesThird[closest_index];
//return float ( pow(cbrt(sqrt(2)), _index-2) );
break;
}
}
void changeAperature(int8_t pchange){ //pchange>0 means more light exposure (brighter image)
uint8_t _newAperatureIndex=findAperatureIndex(setAperature,userSettings.aperatureSelectionMode);
uint8_t _maximumAperatureIndex=0;
switch(userSettings.aperatureSelectionMode){ //check max
case 1: //full stops
_maximumAperatureIndex=sizeof(aperaturesFull)/sizeof(float);
break;
case 2: //half stops
_maximumAperatureIndex=sizeof(aperaturesHalf)/sizeof(float);
break;
case 3: //third stops
_maximumAperatureIndex=sizeof(aperaturesThird)/sizeof(float);
break;
}
_newAperatureIndex-=pchange; //change aperature
_newAperatureIndex=min(_newAperatureIndex,_maximumAperatureIndex-1); //maximum limit
_newAperatureIndex=max(_newAperatureIndex,userSettings.minimumAperatureIndex); //minimum limit
switch(userSettings.aperatureSelectionMode){
case 1: //full stops
setAperature=aperaturesFull[_newAperatureIndex];
break;
case 2: //half stops
setAperature=aperaturesHalf[_newAperatureIndex];
break;
case 3: //third stops
setAperature=aperaturesThird[_newAperatureIndex];
break;
}
}
uint8_t findAperatureIndex(float pAperature,uint8_t pMethod) //find index of closest aperature from given aperature tables (pMethod
{
float _minDistance=90000;
float _lastminDistance=100000;
uint8_t _index=userSettings.minimumAperatureIndex;
uint8_t _maxindexpossible=0;
switch(pMethod){
case 1:
_maxindexpossible=APERATURESFULL_MAXINDEX;
break;
case 2:
_maxindexpossible=APERATURESHALF_MAXINDEX;
break;
case 3:
_maxindexpossible=APERATURESTHIRD_MAXINDEX;
break;
}
2018-03-22 07:57:53 +00:00
while (_lastminDistance>_minDistance) //until distance increases
{
if (_index>_maxindexpossible){ //this index will be out of bounds
return _maxindexpossible;
}
2018-03-22 07:57:53 +00:00
_lastminDistance=_minDistance;
switch(pMethod){
case 1: //full stops
_minDistance=abs( pAperature - aperaturesFull[_index] );
break;
case 2: //half stops
_minDistance=abs( pAperature - aperaturesHalf[_index] );
break;
case 3: //third stops
_minDistance=abs( pAperature - aperaturesThird[_index] );
break;
}
_index++; //next
}
return _index-2; //use index with closest value
2018-03-22 07:57:53 +00:00
}
void changeShutter(int8_t pchange){ //pchange>0 means more light exposure (brighter image)
uint8_t _newShutterIndex=findShutterIndex(setShutter,userSettings.shutterSelectionMode);
uint8_t _maximumShutterIndex=0;
switch(userSettings.shutterSelectionMode){ //get max index from array
case 1:
_maximumShutterIndex=sizeof(shuttertimes1)/sizeof(float);
break;
case 2:
_maximumShutterIndex=sizeof(shuttertimes2)/sizeof(float);
break;
case 3:
_maximumShutterIndex=sizeof(shuttertimes3)/sizeof(float);
break;
2018-03-22 07:57:53 +00:00
}
if (!( -pchange<0 && _newShutterIndex==0)){ //changed value would not yield negative index
_newShutterIndex-=pchange; //change aperature
_newShutterIndex=min(_newShutterIndex,_maximumShutterIndex-1); //maximum limit from array
//_newShutterIndex=min(_newShutterIndex,maximumShutterIndex); //maximum limit from user settings
}
switch(userSettings.shutterSelectionMode){
case 1: //
setShutter=shuttertimes1[_newShutterIndex];
break;
case 2: //
setShutter=shuttertimes2[_newShutterIndex];
break;
case 3: //
setShutter=shuttertimes3[_newShutterIndex];
break;
2018-03-22 07:57:53 +00:00
}
}
uint8_t findShutterIndex(float pShutter,uint8_t pMethod) //find index of closest aperature from given aperature tables (pMethod
{
float _minDistance=0;
switch(userSettings.shutterSelectionMode){
case 1: //
_minDistance=abs(pShutter-shuttertimes1[0]);
break;
case 2: //
_minDistance=abs(pShutter-shuttertimes2[0]);
break;
case 3: //
_minDistance=abs(pShutter-shuttertimes3[0]);
break;
}
2018-03-22 07:57:53 +00:00
float _lastminDistance=_minDistance;
uint8_t _index=0;
uint8_t _maxindexpossible=0;
switch(pMethod){
case 1:
_maxindexpossible=SHUTTERTIMES1_MAXINDEX;
break;
case 2:
_maxindexpossible=SHUTTERTIMES2_MAXINDEX;
break;
case 3:
_maxindexpossible=SHUTTERTIMES3_MAXINDEX;
break;
}
2018-03-22 07:57:53 +00:00
while (_lastminDistance>=_minDistance) //until distance increases
{
if (_index>_maxindexpossible){ //this index will be out of bounds
return _maxindexpossible;
}
2018-03-22 07:57:53 +00:00
_lastminDistance=_minDistance;
switch(pMethod){
case 1:
_minDistance=abs(pShutter - shuttertimes1[_index]);
break;
case 2:
_minDistance=abs(pShutter - shuttertimes2[_index]);
break;
case 3:
_minDistance=abs(pShutter - shuttertimes3[_index]);
break;
2018-03-22 07:57:53 +00:00
}
_index++; //next
}
return _index-2; //use index with closest value
2018-03-22 07:57:53 +00:00
}
void changeISO(int8_t pchange){ //pchange>0 means more light exposure (brighter image), higher iso
uint8_t _newISOIndex=findISOIndex(setISO,userSettings.ISOSelectionMode);
uint8_t _maximumISOIndex=0;
switch(userSettings.ISOSelectionMode){ //get max index from array
case 1:
_maximumISOIndex=sizeof(isoFull)/sizeof(float);
break;
case 2:
_maximumISOIndex=sizeof(isoThird)/sizeof(float);
break;
}
if (!( pchange<0 && _newISOIndex==0)){ //changed value would not yield negative index
_newISOIndex+=pchange; //change iso
_newISOIndex=min(_newISOIndex,_maximumISOIndex-1); //maximum limit from array
//_newISOIndex=min(_newISOIndex,maximumISOIndex); //maximum limit from user settings
}
switch(userSettings.ISOSelectionMode){
case 1: //
setISO=isoFull[_newISOIndex];
break;
case 2: //
setISO=isoThird[_newISOIndex];
break;
}
}
uint8_t findISOIndex(float pISO,uint8_t pMethod) //find index of closest iso from given iso table (pMethod)
{
float _minDistance=abs(pISO-isoFull[0]);
float _lastminDistance=_minDistance;
uint8_t _index=0;
while (_lastminDistance>=_minDistance) //until distance increases
{
_lastminDistance=_minDistance;
switch(pMethod){
case 1:
_minDistance=abs(pISO - isoFull[_index]);
break;
case 2:
_minDistance=abs(pISO - isoThird[_index]);
break;
}
_index++; //next
}
return _index-2;
}
int isoToDIN(float pISO,uint8_t pMethod){
uint8_t _isoIndex=findISOIndex(pISO,pMethod);
switch(pMethod){
case 1:
return isoFullDIN[_isoIndex];
break;
case 2:
return isoThirdDIN[_isoIndex];
break;
}
}
void displayPrintISO(float pISO,bool pDisplayBoth){ //for lower iso values use din notation
if (pISO>=25 || pDisplayBoth){
if (pDisplayBoth){
display.print(pISO,2);
}else{
display.print(pISO,0);
}
}
if (pDisplayBoth){
display.print("/");
}
if (pISO<25 || pDisplayBoth){
display.print(isoToDIN(pISO,userSettings.ISOSelectionMode));
display.write(0xF7); //degree char
}
}
float calculateEV(float pISO, float pShutter, float pAperature)
{ //EV = log2 ( 100* Aperature^2 / (ISO * Time ))
return log (100*pow(pAperature,2) / (pISO*pShutter)) / log (2);
}
2018-03-22 07:57:53 +00:00
void updateDisplay()
{
2018-04-14 11:56:49 +00:00
if (loopmillis-last_displayupdate>=DISPLAY_UPDATEDELAY){
switch(displaymode){
case lightmeter:
updateDisplay_Lightmeter();
break;
case settings:
updateDisplay_Settings();
break;
case meteringmodeselection:
updateDisplay_Meteringmodeselection();
break;
}
last_displayupdate=loopmillis;
display.display();
2018-03-22 07:57:53 +00:00
}
2018-04-14 11:56:49 +00:00
2018-03-22 07:57:53 +00:00
}
void updateDisplay_Lightmeter() //Lightmeter display
{
#define xpos_aperature 2
#define ypos_aperature 29
2018-03-26 15:55:17 +00:00
#define xpos_shutter 50
2018-03-22 07:57:53 +00:00
#define ypos_shutter 29
#define xpos_icon 112 //128-16
#define ypos_icon 29
2018-03-22 07:57:53 +00:00
#define xpos_debug 0
#define ypos_debug 63-7
#define xpos_iso 2
#define ypos_iso 63-7-9
display.clearDisplay();
display.setTextColor(WHITE);
2018-04-14 11:56:49 +00:00
2018-03-22 07:57:53 +00:00
//Aperature
float _showAperature=roundAperature(showAperature,userSettings.aperatureSelectionMode);
display.setTextSize(1);
display.setCursor(xpos_aperature,ypos_aperature); display.print("F");
display.setTextSize(2);
display.setCursor(display.getCursorX(),display.getCursorY()); display.print(int(_showAperature));
if ( int( (_showAperature-int(_showAperature) )*10 ) !=0){ //has a decimal
display.setTextSize(1);
display.setCursor(display.getCursorX()-2,display.getCursorY()+7); display.print("."); display.setCursor(display.getCursorX()+1,display.getCursorY()-7);
display.setTextSize(2);
display.setCursor(display.getCursorX()-2,display.getCursorY());
display.print( (int)round( (_showAperature-int(_showAperature) )*10));
}
//Aperature border
if (setAperature>0){ //Aperature Priority Mode
if (!manualev_mode){ //selection
display.drawRect(xpos_aperature-2, ypos_aperature-2, 40, 18, WHITE); //normal border
}else{ //manual ev selection
drawRectCorners(xpos_aperature-2, ypos_aperature-2, 40, 18, 5,WHITE); //alternative border
}
2018-03-22 07:57:53 +00:00
}
//Shutter
display.setCursor(xpos_shutter,ypos_shutter);
float _showShutter=roundShutter(showShutter,userSettings.shutterSelectionMode);
//Serial.print("rounded Shutter from "); Serial.print(showShutter); Serial.print(" to "); Serial.println(_showShutter); //asdf
if (_showShutter>0.25) //check shuttertime
2018-03-22 07:57:53 +00:00
{ //show full seconds
display.print(int(_showShutter));
if (_showShutter-int(_showShutter)>0){ //has decimals
display.setTextSize(1);
display.setCursor(display.getCursorX()-2,display.getCursorY()+7); display.print("."); display.setCursor(display.getCursorX()+1,display.getCursorY()-7);
display.setTextSize(2);
display.setCursor(display.getCursorX()-2,display.getCursorY());
display.print( (int)round( (_showShutter-int(_showShutter))*10)); //show one decimal
}
display.setTextSize(1); display.setCursor(display.getCursorX(),display.getCursorY()+7);
display.print("s");
}else{ //show fraction of a second
display.setTextSize(1); display.print("1");
display.drawLine(display.getCursorX()+1,display.getCursorY(), display.getCursorX()-1, display.getCursorY()+9, WHITE);
display.setTextSize(2); display.setCursor(display.getCursorX()+2,display.getCursorY());
int _frac_showShutter = (int) ( (1.0f/( (int)(_showShutter*1000000) ) )*1000000 );
display.print( _frac_showShutter );
display.setTextSize(1); display.setCursor(display.getCursorX(),display.getCursorY()+7);
display.print("s");
}
//Shutter border
if (setShutter>0){ //Shutter Priority Mode
if (!manualev_mode){ //selection
display.drawRect(xpos_shutter-2, ypos_shutter-2, 60, 18, WHITE); //normal border
}else{ //manual ev selection
drawRectCorners(xpos_shutter-2, ypos_shutter-2, 60, 18, 5, WHITE); //alternative border
}
2018-03-22 07:57:53 +00:00
}
//Draw line for ev error
float _actualEV = calculateEV(setISO,_showShutter,_showAperature);
float _evError=_actualEV-ev; //Line on the right means suggested values will overexpose the image
uint8_t evErrorX=0;
uint8_t evErrorY=ypos_aperature+16;
if (setAperature>0){ //Aperature Priority Mode
evErrorX=xpos_shutter+20;
evErrorY=ypos_shutter+16;
}else if(setShutter>0) { //Shutter Priority Mode
evErrorX=xpos_aperature+20;
evErrorY=ypos_aperature+16;
}
uint8_t everrorpixels_per_ev=20;
if (_evError>1 || _evError<1){ //scale smaller if error greater 1 EV
everrorpixels_per_ev=10;
}
display.drawLine(evErrorX,evErrorY,evErrorX,evErrorY+1,WHITE); //center line
display.drawLine(evErrorX-everrorpixels_per_ev,evErrorY,evErrorX-everrorpixels_per_ev,evErrorY+1,WHITE); //-1 ev
display.drawLine(evErrorX+everrorpixels_per_ev,evErrorY,evErrorX+everrorpixels_per_ev,evErrorY+1,WHITE); //+1ev
if (_evError>1 || _evError<1){ //scale smaller if error greater 1 EV
display.drawLine(evErrorX-2*everrorpixels_per_ev,evErrorY,evErrorX-2*everrorpixels_per_ev,evErrorY+1,WHITE); //-1 ev
display.drawLine(evErrorX+2*everrorpixels_per_ev,evErrorY,evErrorX+2*everrorpixels_per_ev,evErrorY+1,WHITE); //+1ev
}
display.drawLine(evErrorX,evErrorY,evErrorX+(everrorpixels_per_ev*_evError+0.5),evErrorY,WHITE); //Draw ev error line
//Meteringmode Icon
if (meteringmode == METERINGMODE_REFLECTIVE){
2018-03-26 15:55:17 +00:00
display.drawXBitmap(xpos_icon, ypos_icon, icon_spot_bits, icon_spot_width, icon_spot_height, WHITE);
}else if (meteringmode == METERINGMODE_INCIDENT) {
2018-03-26 15:55:17 +00:00
display.drawXBitmap(xpos_icon, ypos_icon, icon_incident_bits, icon_incident_width,icon_incident_height, WHITE);
}
2018-03-22 07:57:53 +00:00
//ISO
display.setCursor(xpos_iso,ypos_iso); display.setTextSize(1);
if (setISO<25){
display.print("DIN "); //below iso 25 only din value is shown here
}else{
display.print("ISO ");
}
displayPrintISO(setISO,false);//display.print(formatISO(setISO,false));
2018-04-14 11:56:49 +00:00
2018-03-26 15:55:17 +00:00
//EV Scale
2018-05-02 08:41:24 +00:00
uint8_t _evrangedisplay=10;//which range to display. Default value
if (ev_min>-254 && ev_max>-254){ //values set
_evrangedisplay=ev_max-ev_min;
}
2018-05-02 08:41:24 +00:00
if (_evrangedisplay<6){ //minimum range
_evrangedisplay=6;
}
2018-03-26 15:55:17 +00:00
2018-05-02 08:41:24 +00:00
//#define FULLEVLINEDISTANCE 9
//#define THIRDEVLINEDISTANCE 3
uint8_t FULLEVLINEDISTANCE=((int)(WIDTH/(_evrangedisplay+2))/3)*3; //scale distance to fit evrange_display with safety margin, floor to multiples of 3
uint8_t THIRDEVLINEDISTANCE=FULLEVLINEDISTANCE/3;
uint8_t _max_evvalues_displayed=(WIDTH/(FULLEVLINEDISTANCE));
2018-03-26 15:55:17 +00:00
#define ypos_evtext 7
#define ypos_icon_arrow 6
2018-05-02 08:41:24 +00:00
int8_t _startev=-5; //first ev to display, 13 ev values can fit on screen
/*if (ev>2 && (ev_min<-254 || ev_min>2)){ //TODO make ev scale start better
_startev=0;
}
if (ev>_max_ev_displayed-2 || ev_max>_max_ev_displayed-2){
_startev=5+ev-(_max_ev_displayed-2);
}*/
float _evrangemargin=(_max_evvalues_displayed-_evrangedisplay)/2.0; //space left on both sides between evnrange (min to max) and display width
if (_evrangemargin<0){ //bound
_evrangemargin=0;
}
if (ev_min>-254 && ev_max>-254 ){ //minmax values set
if (ev>=ev_min && ev<=ev_max){ //arrow between min and max
_startev=(ev_max-ev_min)/2+ev_min - _max_evvalues_displayed/2; //center of evmin and max at display center
}else{ //arrow outside of ev min max range
if (ev<ev_min) { //on the left
_startev=ev-_evrangemargin-2;
}else if (ev>ev_max) { //on the right
_startev=ev+_evrangemargin-_evrangedisplay;
}
}
}else{ //ev min max values not set yet
_startev=ev-_max_evvalues_displayed/2; //center
_startev=(int(_startev/(_max_evvalues_displayed/2)))*(_max_evvalues_displayed/2); //floor to multiples of (_evrangedisplay/2)
}
uint8_t xpos_arrow=(ev-_startev*1.0) *FULLEVLINEDISTANCE+1; //calculate display position for ev
2018-03-26 15:55:17 +00:00
display.setTextSize(1);
display.drawLine(THIRDEVLINEDISTANCE,0,THIRDEVLINEDISTANCE,0,WHITE); //first third line
display.drawLine(THIRDEVLINEDISTANCE+THIRDEVLINEDISTANCE,0,THIRDEVLINEDISTANCE+THIRDEVLINEDISTANCE,0,WHITE); //second third line
2018-05-02 08:41:24 +00:00
for (uint8_t _fullevline=1;_fullevline<=_max_evvalues_displayed;_fullevline++){ //with fullevlindistance=9 and WIDTH=128 -> <=13
int8_t _current_evvalue = _fullevline+_startev;
2018-03-26 15:55:17 +00:00
uint8_t _xpos_center_evtext = _fullevline*FULLEVLINEDISTANCE; //center of current ev line x pos
display.drawLine(_xpos_center_evtext,0,_xpos_center_evtext,2,WHITE);
display.drawLine(_xpos_center_evtext+THIRDEVLINEDISTANCE,0,_xpos_center_evtext+THIRDEVLINEDISTANCE,0,WHITE);
display.drawLine(_xpos_center_evtext+THIRDEVLINEDISTANCE+THIRDEVLINEDISTANCE,0,_xpos_center_evtext+THIRDEVLINEDISTANCE+THIRDEVLINEDISTANCE,0,WHITE);
2018-05-02 08:41:24 +00:00
if ((FULLEVLINEDISTANCE>9 && _current_evvalue<10 && _current_evvalue>=0) || (FULLEVLINEDISTANCE>12) || _fullevline%2==1){ //display every single digit ev if distance greater 9 OR if dist. gr. 12 OTHERWISE only every second digit
2018-03-26 15:55:17 +00:00
uint8_t _evtextmove=2; //movement of left point of text to the left. Compensation for center position
if (_current_evvalue>9 || _current_evvalue<0){ //text has two digits
2018-03-26 15:55:17 +00:00
_evtextmove=5;
}
if ( (xpos_arrow-7 > _xpos_center_evtext) || (xpos_arrow+7 < _xpos_center_evtext) ) { //drawn arrow not too close to ev text
display.setCursor(_xpos_center_evtext-_evtextmove,ypos_evtext); display.print(_current_evvalue); //EV Text at scale line
2018-03-26 15:55:17 +00:00
}
}
}
//Arrow at current ev
float _ev_decimals=abs(ev-((int)ev));
2018-03-26 15:55:17 +00:00
display.drawXBitmap(xpos_arrow - icon_arrow_width/2.0, ypos_icon_arrow, icon_arrow_bits, icon_arrow_width, icon_arrow_height, WHITE); //arrow icon
if (manualev_mode){ //in manual ev mode
display.drawXBitmap(xpos_arrow - icon_arrow_width/2.0 -1, ypos_icon_arrow, icon_arrow_bits, icon_arrow_width, icon_arrow_height, WHITE); //arrow icon //draw bold
display.drawXBitmap(xpos_arrow - icon_arrow_width/2.0 +1, ypos_icon_arrow, icon_arrow_bits, icon_arrow_width, icon_arrow_height, WHITE); //arrow icon //draw bold
display.drawXBitmap(xpos_arrow - icon_arrow_width/2.0 , ypos_icon_arrow-1, icon_arrow_bits, icon_arrow_width, icon_arrow_height, WHITE); //arrow icon //draw bold
}
2018-03-26 15:55:17 +00:00
uint8_t _xpos_current_evtext_move=5; //for text centering
if (_ev_decimals <= 0.1666 || _ev_decimals > 0.8333) { //without fraction displayed
_xpos_current_evtext_move=2;
}
int _displayev=(int)ev;
2018-03-26 15:55:17 +00:00
if (_ev_decimals > 0.8333 ){
if (ev>=0){ //ev is positive
_displayev=(int)(ev+1);//EV Value under arrow. Ceil
}else if (ev<0){ //ev is negative
_displayev=(int)(ev-1);//EV Value under arrow. Ceil (negative)
}
2018-03-26 15:55:17 +00:00
}
//int _xpos_current_fraction_move=0; //move fraction icon
if (_displayev>=10 || ev<-0.1666){ //displayev is two digits long (>=10 or negative sign)
2018-04-14 11:56:49 +00:00
_xpos_current_evtext_move+=6; //move digits to left. positive means left
}
display.setCursor(xpos_arrow-_xpos_current_evtext_move,ypos_icon_arrow+icon_arrow_height+2); //current ev text position
if (ev<0 && _displayev==0){ //ev is negative but displayev is zero
display.print("-"); // add minus in front
}
display.print(_displayev); //EV Value under arrow
2018-03-26 15:55:17 +00:00
if ( _ev_decimals > 0.1666 && _ev_decimals <= 0.4166) {
display.drawXBitmap(xpos_arrow , ypos_icon_arrow+icon_arrow_height-(icon_one_third_height-8)/2 +2, icon_one_third_bits, icon_one_third_width, icon_one_third_height, WHITE); //one third
}else if ( _ev_decimals > 0.4166 && _ev_decimals <= 0.5833) {
display.drawXBitmap(xpos_arrow , ypos_icon_arrow+icon_arrow_height-(icon_one_half_height-8)/2 +2, icon_one_half_bits, icon_one_half_width, icon_one_half_height, WHITE); //one half
}else if ( _ev_decimals > 0.5833 && _ev_decimals <= 0.8333) {
display.drawXBitmap(xpos_arrow , ypos_icon_arrow+icon_arrow_height-(icon_two_third_height-8)/2 +2, icon_two_third_bits, icon_two_third_width, icon_two_third_height, WHITE); //two third
}
//ev min & max
2018-05-02 09:27:10 +00:00
int16_t xpos_ev_min=(ev_min-_startev*1.0) *FULLEVLINEDISTANCE; //calculate display position for ev
int16_t xpos_ev_max=(ev_max-_startev*1.0) *FULLEVLINEDISTANCE; //calculate display position for ev
bool arrow_is_between_minmax=true;
2018-05-02 08:41:24 +00:00
if (xpos_arrow<=xpos_ev_min || xpos_arrow>=xpos_ev_max){
arrow_is_between_minmax=false; //selected ev is not between min and max ev
}
2018-05-02 08:41:24 +00:00
if (ev_min>-254 && xpos_ev_min>=0 && xpos_ev_min<WIDTH){ //ev_min is set (-255 is placeholder for "not set")
display.drawLine(xpos_ev_min,2,xpos_ev_min,5,WHITE);
if ((xpos_arrow-xpos_ev_min)>3 && arrow_is_between_minmax){ //arrow is not overlaying line and is in between min and max
2018-05-02 08:41:24 +00:00
//display.drawLine(xpos_ev_min,4,xpos_arrow ,4,WHITE); //line from left horizontally to arrow
display.drawLine(xpos_ev_min,5,xpos_arrow - 4,5,WHITE); //line from left horizontally to arrow
}
}
2018-05-02 08:41:24 +00:00
if (ev_max>-254 && xpos_ev_max>=0 && xpos_ev_max<WIDTH){ //ev_min is set (-255 is placeholder for "not set")
display.drawLine(xpos_ev_max,2,xpos_ev_max,5,WHITE);
if ((xpos_ev_max-xpos_arrow)>3 && arrow_is_between_minmax){ //arrow is not overlaying line and is in between min and max
2018-05-02 08:41:24 +00:00
//display.drawLine(xpos_ev_max,4,xpos_arrow ,4,WHITE); //line from right horizontally to arrow
display.drawLine(xpos_ev_max,5,xpos_arrow + 2,5,WHITE); //line from right horizontally to arrow
}
}
2018-05-02 08:41:24 +00:00
if (ev_min>-254 && ev_max>-254){ //evmin and max are set
2018-05-02 09:27:10 +00:00
uint8_t _xpos_ev_min_line=xpos_ev_min;
uint8_t _xpos_ev_max_line=xpos_ev_max;
if (xpos_ev_min<0){
_xpos_ev_min_line=0;
}else if (xpos_ev_min>=WIDTH-1){
_xpos_ev_min_line=WIDTH-1;
}
if (xpos_ev_max<0){
_xpos_ev_max_line=0;
}else if (xpos_ev_max>=WIDTH-1){
_xpos_ev_max_line=WIDTH-1;
}
display.drawLine(_xpos_ev_min_line,4,_xpos_ev_max_line ,4,WHITE); //draw single line between them
2018-05-02 08:41:24 +00:00
}
for (int8_t i=-(xpos_arrow-xpos_ev_min)/FULLEVLINEDISTANCE;i<(xpos_ev_max-xpos_arrow)/FULLEVLINEDISTANCE;i++){ //draw black lines for every zone border
display.drawLine(xpos_arrow+i*FULLEVLINEDISTANCE+FULLEVLINEDISTANCE/2,4,xpos_arrow+i*FULLEVLINEDISTANCE+FULLEVLINEDISTANCE/2 ,5,BLACK); //erase part of horizontal line
}
2018-04-14 11:56:49 +00:00
2018-03-26 15:55:17 +00:00
2018-03-22 07:57:53 +00:00
//DEBUG Message
display.setTextSize(1);
display.setCursor(xpos_debug,ypos_debug);
display.print(vbat,2);
2018-03-22 07:57:53 +00:00
display.print("V ");
/*display.print("Ev=");
2018-03-22 07:57:53 +00:00
display.print(ev);
display.print(" |");
2018-04-14 11:56:49 +00:00
display.print(incident);*/
/*display.print(debug_analog_low);
2018-04-14 11:56:49 +00:00
display.print(" : ");
display.print(debug_analog_high);*/
/*display.print(ev_min,1);
display.print("<");
display.print(ev,1);
display.print("<");
display.print(ev_max,1);*/
display.setCursor(xpos_debug+50,ypos_debug-5);
if (ev_min>-254 && ev>=ev_min) { //ev min set
display.print("-");
display.print(ev-ev_min,1);
}else{
display.print("/");
}
display.print(" <> ");
if (ev_max>-254 && ev<=ev_max){
display.print("+");
display.print(ev_max-ev,1);
}else{
display.print("/");
}
2018-03-22 07:57:53 +00:00
}
void updateDisplay_Settings()
{
display.clearDisplay();
display.setTextColor(WHITE);
display.setTextSize(1);
#define SETTINGS_YPOS_INCREMENT 9
#define SETTINGS_XPOS_OFFSET 1
display.setCursor(SETTINGS_XPOS_OFFSET,0); //absolute position for first item
for (uint8_t _currentItemIndex=0;_currentItemIndex<=SETTINGS_SELECTEDITEM_MAX;_currentItemIndex++)
{
if (settings_selectedItem==_currentItemIndex){
if (settings_itemActive){
display.drawRect(0, display.getCursorY()-2, 126 , 11, WHITE);
}else{
display.fillCircle(2, display.getCursorY()+3,2, WHITE); //x,y,r,color
}
display.setCursor(display.getCursorX()+5,display.getCursorY()); //move text to the right
}
display.print(settingStrings[_currentItemIndex]);
switch(_currentItemIndex){ //if values need to be shown
case 0: displayPrintISO(setISO,true);//display.print(formatISO(setISO,true));
2018-03-22 07:57:53 +00:00
break;
case 1: display.print(settingsnameAperatureSelectionMode[userSettings.aperatureSelectionMode-1]);
break;
case 2: display.print(settingsnameShutterSelectionMode[userSettings.shutterSelectionMode-1]);
break;
case 3: display.print("1/"); display.print(userSettings.manualev_moveamount_frac);display.print(" EV");
break;
//case 4 is power off, no value to display here
2018-03-22 07:57:53 +00:00
}
display.setCursor(SETTINGS_XPOS_OFFSET,display.getCursorY()+SETTINGS_YPOS_INCREMENT); //move cursor to next entry
}
2018-03-26 15:55:17 +00:00
}
2018-03-22 07:57:53 +00:00
2018-03-26 15:55:17 +00:00
void updateDisplay_Meteringmodeselection()
{
display.clearDisplay();
display.setTextColor(WHITE);
#define xpos_center_icon_spot 30
#define ypos_icon_spot 20
#define xpos_center_icon_incident 97
#define ypos_icon_incident 20
2018-03-22 07:57:53 +00:00
2018-03-26 15:55:17 +00:00
display.drawXBitmap(xpos_center_icon_spot-icon_spot_width/2, ypos_icon_spot, icon_spot_bits, icon_spot_width, icon_spot_height, WHITE); //Spot icon
display.drawRect(xpos_center_icon_spot-icon_spot_width/2-2, ypos_icon_spot-2, icon_spot_width+4,icon_spot_height+4,WHITE);
display.drawXBitmap(xpos_center_icon_incident-icon_incident_width/2, ypos_icon_incident, icon_incident_bits, icon_incident_width, icon_incident_height, WHITE); //incident icon
display.drawRect(xpos_center_icon_incident-icon_incident_width/2-2, ypos_icon_incident-2, icon_incident_width+4,icon_incident_height+4,WHITE);
2018-03-22 07:57:53 +00:00
2018-03-26 15:55:17 +00:00
display.setTextSize(1);
display.setCursor(xpos_center_icon_spot-10,ypos_icon_spot+icon_spot_height +6); //text position upper left
display.print("SPOT"); //7x5 characters, xpos_center_icon_spot-(5*#chars /2)
display.setCursor(xpos_center_icon_incident-20,ypos_icon_incident+icon_incident_height+6); //text position upper left
display.print("INCIDENT");
2018-04-14 11:56:49 +00:00
if (loopmillis-millis_opened_meteringmodeselection>=DELAY_METERINGMODESELECTION_FLASHLIGHT){
blinkLED(500); //turn led on continously
}
2018-03-22 07:57:53 +00:00
}
void drawRectCorners(uint8_t px,uint8_t py, uint8_t pw, uint8_t ph, uint8_t pcornerlength, uint8_t pc){
//px py are top left
display.drawLine(px,py,px+pcornerlength,py, pc);
display.drawLine(px,py,px,py+pcornerlength, pc);
display.drawLine(px+pw,py, px+pw-pcornerlength,py, pc);
display.drawLine(px+pw,py, px+pw,py+pcornerlength, pc);
display.drawLine(px+pw,py+ph, px+pw-pcornerlength,py+ph, pc);
display.drawLine(px+pw,py+ph, px+pw,py+ph-pcornerlength, pc);
display.drawLine(px,py+ph, px+pcornerlength,py+ph, pc);
display.drawLine(px,py+ph, px,py+ph-pcornerlength, pc);
}
2018-04-14 11:56:49 +00:00
void blinkLED(long duration){
blinkLED(duration,255);
}
void blinkLED(long duration,uint8_t brightness){
//digitalWrite(PIN_LED,HIGH);
analogWrite(PIN_LED,brightness);
2018-04-14 11:56:49 +00:00
millis_ledoff=loopmillis+duration;
}
void checkLED(){
if (loopmillis>=millis_ledoff && digitalRead(PIN_LED)){
//digitalWrite(PIN_LED,LOW);
analogWrite(PIN_LED,0); //LED OFF
2018-04-14 11:56:49 +00:00
}
}
template <class T> int EEPROM_writeAnything(int ee, const T& value)
{ //from http://www.stm32duino.com/viewtopic.php?t=1576
const byte* p = (const byte*)(const void*)&value;
unsigned int i;
for (i = 0; i < sizeof(value); i++)
EEPROM.write(ee++, *p++);
return i;
}
template <class T> int EEPROM_readAnything(int ee, T& value)
{
byte* p = (byte*)(void*)&value;
unsigned int i;
for (i = 0; i < sizeof(value); i++)
*p++ = EEPROM.read(ee++);
return i;
}