crashtest-r0ket/firmware/funk/nrf24l01p.c

#include <basic/basic.h>
#include <nrf24l01p.h>
#include "core/ssp/ssp.h"

#define CHANNEL_BEACON 81
#define DEFAULT_SPEED R_RF_SETUP_DR_2M
#define MAC_BEACON "BEACO"

/*-----------------------------------------------------------------------*/
/* Transmit a byte via SPI                                               */
/*-----------------------------------------------------------------------*/
inline void xmit_spi(uint8_t dat) {
    sspSend(0, (uint8_t*) &dat, 1);
}

#define CS_LOW()    gpioSetValue(RB_SPI_NRF_CS, 0)
#define CS_HIGH()   gpioSetValue(RB_SPI_NRF_CS, 1)
#define CE_LOW()    gpioSetValue(RB_NRF_CE, 0)
#define CE_HIGH()   gpioSetValue(RB_NRF_CE, 1)

void nrf_cmd(uint8_t cmd){
    CS_LOW();
    xmit_spi(cmd);
    CS_HIGH();
};

uint8_t nrf_cmd_status(uint8_t cmd){
    CS_LOW();
    sspSendReceive(0, &cmd, 1);
    return cmd;
    CS_HIGH();
};

void nrf_cmd_rw_long(uint8_t* data, int len){
    CS_LOW();
    sspSendReceive(0,data,len);
    CS_HIGH();
};


void nrf_write_reg(const uint8_t reg, const uint8_t val){
    CS_LOW();
    xmit_spi(C_W_REGISTER | reg);
    xmit_spi(val);
    CS_HIGH();
};

void nrf_read_long(const uint8_t cmd, int len, uint8_t* data){
    CS_LOW();
    xmit_spi(cmd);
    for(int i=0;i<len;i++)
        data[i] = 0x00;
    sspSendReceive(0,data,len);
    CS_HIGH();
};

void nrf_write_long(const uint8_t cmd, int len, uint8_t* data){
    CS_LOW();
    xmit_spi(cmd);
    sspSend(0,data,len);
    CS_HIGH();
};

#define nrf_write_reg_long(reg, len, data) \
    nrf_write_long(C_W_REGISTER|reg, len, data)

void nrf_init() {
    // Enable SPI correctly
    sspInit(0, sspClockPolarity_Low, sspClockPhase_RisingEdge);

    // Enable CS & CE pins
    gpioSetDir(RB_SPI_NRF_CS, gpioDirection_Output);
    gpioSetPullup(&RB_SPI_NRF_CS_IO, gpioPullupMode_Inactive);
    gpioSetDir(RB_NRF_CE, gpioDirection_Output);
    gpioSetPullup(&RB_NRF_CE_IO, gpioPullupMode_PullUp);

    // Setup for nrf24l01+
    // power up takes 1.5ms - 3.5ms (depending on crystal)
    CS_LOW();
    nrf_write_reg(R_CONFIG,
            R_CONFIG_PRIM_RX| // Receive mode
            R_CONFIG_PWR_UP|  // Power on
            R_CONFIG_CRCO     // 2-byte CRC
            );
    
    nrf_write_reg(R_EN_AA, 0); // Disable Enhanced ShockBurst;

    nrf_write_reg(R_RF_CH, CHANNEL_BEACON &127); // Select channel

    // enable receive pipes
    nrf_write_reg(R_EN_RXADDR,R_EN_RXADDR_ERX_P0 
//            |R_EN_RXADDR_ERX_P1
            );

    nrf_write_reg(R_RX_PW_P0,16);
    nrf_write_reg_long(R_RX_ADDR_P0,5,(uint8_t*)"\x1\x2\x3\x2\1");

//    nrf_write_reg(R_RX_PW_P1,16);
//    nrf_write_reg_long(R_RX_ADDR_P1,5,"R0KET");

    // OpenBeacon transmit address
    nrf_write_reg_long(R_TX_ADDR,5,(uint8_t*)MAC_BEACON);

    // Set speed / strength
    nrf_write_reg(R_RF_SETUP,DEFAULT_SPEED|R_RF_SETUP_RF_PWR_3);

    // XXX: or write R_CONFIG last?
};

int nrf_rcv_pkt_time(int maxtime, int maxsize, uint8_t * pkt){
    char buf;
    int len;

    nrf_write_reg(R_CONFIG,
            R_CONFIG_PRIM_RX| // Receive mode
            R_CONFIG_PWR_UP|  // Power on
            R_CONFIG_CRCO     // 2-byte CRC
            );
    CE_HIGH();
    delayms(maxtime); // XXX: check interrupt?
    CE_LOW();
    len=1;
    nrf_read_long(C_R_RX_PL_WID,len,&buf);
    len=buf;
    if(len>32 || len==0){
        return 0; // no packet
    };
    if(len>maxsize){
        return -1; // packet too large
    };
    nrf_read_long(C_R_RX_PAYLOAD,len,pkt);
    CS_HIGH();
    return len;
};

char nrf_snd_pkt_crc(int size, uint8_t * pkt){

    nrf_write_reg(R_CONFIG,
            R_CONFIG_PWR_UP|  // Power on
            R_CONFIG_CRCO     // 2-byte CRC
            );
    
    nrf_write_long(C_W_TX_PAYLOAD,size,pkt);

    CE_HIGH();
    delayms(10); // Send it.  (only needs >10ys, i think)
    CE_LOW();

    return nrf_cmd_status(C_NOP);
};